Can be operate control valve without positioning if yes ?
how and why?

Answers were Sorted based on User's Feedback



Can be operate control valve without positioning if yes ? how and why?..

Answer / varun bhardwaj

With out positioner we can operate small size of valves,
but for large sizes of valves , we required Positioner.
Due to force balance principle, the positioner give us a
better accuracy than with out positioner.

Is This Answer Correct ?    6 Yes 1 No

Can be operate control valve without positioning if yes ? how and why?..

Answer / sanjoy panda

Without position-er all the control valve operate but it operating criteria is not satisfy our requirement. Error will be produced very large, and response will be very slow . To avoid on those error we have to use position-er.

Is This Answer Correct ?    4 Yes 0 No

Can be operate control valve without positioning if yes ? how and why?..

Answer / ravi

Without positioner control valve will become on off valve because position feedback dose not transist.

If control valves are able to operate within 3 - 15 psi, that case can possible though I/p converter .

Is This Answer Correct ?    1 Yes 0 No

Can be operate control valve without positioning if yes ? how and why?..

Answer / sunny

No without positioner we canot operate control valve

Is This Answer Correct ?    4 Yes 7 No

Post New Answer

More Instrumentation Interview Questions

what is the zero elevation and zero supresstion in level measurement, how can use it?

2 Answers   GAIL,


HOW DPT WORKS?

6 Answers   Essar,


what is cascade loop and how it work and why it used instead of PID single loop? In cascade, Which loop is faster and slower? Please explain with loop drawing and example...

2 Answers   Honeywell,


what is the calibration standard for pressure and differential pressure transmitters?

1 Answers   Thermax,


How can we loop powered for a transmitter.How we can do wiring

1 Answers  






there are two candidates p and q in an election.During the campaign,40% of the voters promised to vote for P ,and rest for Q.however, on the day of election 15% of the voter went back on their promise to vote for P and instead voted for Q. 25% of the voters went back on their promise to vote for Q and instead voted for P.suppose,P lost by two votes,then what was the total no. of voters.

1 Answers   GATE,


how eddy current loss in probe and induced gap voltage accros probe trip and shaft

1 Answers   Reliance,


my temperature transmitter in field showing 700 degree , whereas in dcs showing 459 degree, how to resolve this?

4 Answers   ONGC,


what is the PC interface and software for connection to ABB logic module “ LM011-CE18RAC “ ( for Programming ) ??

0 Answers  


Where & Why we are using SURGE PROTECTION ?

4 Answers   IOCL,


What is motion balance principle?

0 Answers  


How will you calibrate an interface level trol/normal level trol in line and in w/s?

1 Answers   CCIE,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)