Where are u provide laps in columns & beams?

Answers were Sorted based on User's Feedback



Where are u provide laps in columns & beams?..

Answer / ratheesh

Column - Mid of the span u can lap, Min 50% rods only lap in
a floor.
Beam - should be lap in one, third of length. don't lap in
mid span....

Is This Answer Correct ?    26 Yes 5 No

Where are u provide laps in columns & beams?..

Answer / madhu sudhan

LAPPING FOR COLUMN:- MID HEIGHT OF COLUMN WITH 1.3LD,NOT
MORE THAN 50% OF BARS LAPPED IN ONE STRETCH,THE VERTICAL
DISTANCE BETWEEN LAP NOT LESS THAN 0.3TIMES LAP LENGTH.

BEAMS:- MID SPAN OF COMPRESSION ZONE.

REFFER CODE IS 13920

Is This Answer Correct ?    18 Yes 5 No

Where are u provide laps in columns & beams?..

Answer / sivraj

Beam top bars lapping should provide at mid span of beam or bottom bars of beam lapping should provide at near end support.

Is This Answer Correct ?    7 Yes 0 No

Where are u provide laps in columns & beams?..

Answer / thangam.

Columns & Beams Laps are Provided in Mid Span.

Is This Answer Correct ?    5 Yes 29 No

Post New Answer

More Civil Engineering Interview Questions

WHAT IS NON DESTRUCTIVE TEST?PLEASE GIVE ME THE PROCEDURE?

3 Answers  


what is the formula of concrete quantity

4 Answers   NKB, Soma Enterprises,


all technical question

0 Answers   L&T,


how to design a formwork for beam, how to determine the load baring capacity of the cuplock system and which is the relevant code for the same.

0 Answers   ACIL,


The slenderness ratio of a column is zero when its length ??

2 Answers   SSC,






how to calculate 1:2:4 ratio concrete cement, sand, metal and water please give me brief calculation

34 Answers   Call Centre, CCCL, Oracle, RLM, RPP, Sunanda Infra, Sunrise Enterprises,


what is the coefficient for running feet to cft coversion both area and price

0 Answers  


What you understand by richter scale?

0 Answers  


How much for the BRC lapping in full yield and half yield < and which table to get it ?

0 Answers   Engtex,


16. What do you consider to be your greatest achievement so far and why?

2 Answers  


what are some possible sources of error in the CBR test?

1 Answers  


2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;2+2=?;

1 Answers   TCS,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)