Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


What is ideal location for cube casting, RMC vehical at
Ground Floor and Slab casting at 40th Floor

Answers were Sorted based on User's Feedback



What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / santosh singh

at ground floor .....near vehicle

Is This Answer Correct ?    5 Yes 3 No

What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / balakrishna bedudoori

I think the ideal location for cube casting is near Slab
casting at 40th floor, because if we take concrete from RMC
vehicle at ground floor, free falling height of concrete
from the vehicle to the ground is generally more than 1.5m,
which can lead to seggregation of concrete, which is not
good for taking moulds.

Is This Answer Correct ?    5 Yes 4 No

What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / sumit

If Gap between TM chute and Ground floor more than 1.5
Mtr.so you not permitted cube casting on ground floor.
then the option is cube casting on 40th floor

Is This Answer Correct ?    3 Yes 2 No

What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / prasanna

Since atleast 6 cubes are taken for a batch of concrete, it
is advisable to take 3 each at both location, so that we get
clarity on workability of concrete.Average result of these 6
cubes will hold good.

Is This Answer Correct ?    1 Yes 0 No

What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / jyoti ranjan

actually it should be what type of conc. we r going to pour at a area,weather it is M35 and above then it must be in g floor but cube must be cast at pouring point.

Is This Answer Correct ?    0 Yes 0 No

What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / sobhanbabu

at the 40th floor only.pumping jurney takes nearly 10
minutes.during pumping heat generates.

Is This Answer Correct ?    1 Yes 2 No

What is ideal location for cube casting, RMC vehical at Ground Floor and Slab casting at 40th Floo..

Answer / sudhir shetty

Its at the ground floor because during pumping there will be
some loss of slurry etc which is calculated during designing
of structure after which required strength is calculated. If
its taken in 40th floor u will not get the perfect sampling.

Is This Answer Correct ?    0 Yes 1 No

Post New Answer

More Civil Engineering Interview Questions

Define What is passive earth pressure ?

0 Answers  


what is porosity??

3 Answers  


A doubly reinforced concrete beam is 25 cm wide and 50cm deep to the centre of tension reinforcement. The centre of compression is steel is 5cm from the compression edge. The areas of the compression and the tension steel are 10.16cm2 and 12.56 cm2 if m=18 and the bending moment at the section is 7,000,000 N-cm. Calculate the stress in concrete and steel.

0 Answers  


The resultant upthrust on a body partially immersed in a liquid acts through?

5 Answers   TNPSC Tamil Nadu Public Service Commission,


20 mpa what is the quantity of cement sand and aggregate in one cubic meter of pcc non rainforcement concreate kindly answer including formaula thanks

0 Answers  


what is the multiplying factor for diffrent types of pcc/rcc ratios?

2 Answers   L&T,


is there any books available to know the methodology of construction process ( Site Process ) and also find the quantities of all materials used at site.

1 Answers  


what is the status of Brick & cube testing

1 Answers   Ascent,


What is the difference between single reinforcement

7 Answers   L&T,


how would you describe yourself and your ideal job

3 Answers  


LET ME KNOW HOW IS CALCULATE RUBBLE WALL .3'00" IN BOTTOM 1' 6" IN TOP HEIGHT 8' 0" AVERAGE. length 200'00". please give correct answer.

0 Answers  


I am a civil engineering student and going to attend interview in this week in an IT company.Will they ask me questions about my area of interest or cs

0 Answers   Satyam,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)