What are the automatic controller MODES?

Answers were Sorted based on User's Feedback



What are the automatic controller MODES?..

Answer / uncontrol

Following are the mode of control. Ratio Control, PID
Control, PI Control, ON/OFF Control, Cascade Control,
Override Control, Feedback Control, Feed Froward Control.
These control are can be set in to MAN and AUTO Mode, If
this in MANUAL the mode of control is disable, If this is in
AUTO the mode of control is enable.

Is This Answer Correct ?    14 Yes 0 No

What are the automatic controller MODES?..

Answer / omak

In automatic controller there are two modes available to control the process. One is called Automatic mode, it will control the process automatically by comparing the feedback input with the set point. The another method called Manual mode, in this mode the operater check the measured input from the field and give the command manually for the final control element.

Is This Answer Correct ?    7 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

What is the Relation Between flow and pressure. How both terms related with each other.

1 Answers  


What is the difference between conductive lined pipe and conductive unlined pipe? Why do we see that?

0 Answers   Process Control Technologies,


what is linerity and non-linearity?

2 Answers  


IN CONTROL VALVE SPECIFICATIONS GENERALLY TERM " DE- 200" ."DM -400"USED,, WHAT IS DE/ DM STANDS FOR?

0 Answers  


whats the working principle of level transmeter?

6 Answers  






What should be hight of CONTROL panel for access & OPERATION What is BIS & INDIAN STD for SAME?

3 Answers  


what is the difference between Digital output DO signals /Commands for start/stop and Solenoid valves ??

1 Answers  


I have installed a RTD whose length is 2250mm(RTD stem length), but it's upper 200 -250mm is out of the reactor, and this upper 200mm stem is surrounded by atmospheric temp. And the lower portion i.e. 2000mm is in contact with the measuring fluid, then does the final measuring temp. Gonna change as the upper 200mm RTD stem is out of reactor?

1 Answers   Process Control Technologies,


how to calibrate temprature switch and flow switch ?

1 Answers   Adgas,


I want to measure level under vaccum by using DP Tx and vaccum vary between -500 to -670 mmHg and process fluid is accetic anhydride if consider process fluid density 1 kg/cm2. how to calibrate Tx ? consider level is 0 to 100 Cm.

1 Answers   CCC,


What is the difference between local indicator(flow) and flow indicator?

2 Answers  


What should be the ideal tapping location for pressure differential transmitter for liquid service. If the tapping taken from the top of the pipe then PDIT will work properly or not. If PDIT do not work properly then what minimum corrective action should be taken in order to solve wrong tapping locations.

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)