Answer / manoj kumar

The coefficient of performance or COP (sometimes CP) of a heat pump is the ratio of the heating or cooling provided over the electrical energy consumed. The COP was created to compare heat pump systems according to their energy efficiency.

A level of performance that describes a process that uses the lowest amount of inputs to create the greatest amount of outputs. Efficiency relates to the use of all inputs in producing any given output, including personal time and energy.

COP of Heat Pump = 1 + COP of the Refrigerator

The COP of the refrigerator and air-conditioner can be less than one or greater than one. The above formula also shows that the COP of the heat pump can never be less than one; it is always more than one.

Answer / sisin

cop(coefficient of performance ) the effectiveness of refrigeration is expressed as(cop).
cop=(desired refrigeration effect/work spent in producing refrigeration effect)
, efficiency is=output/input(here the out put is refrigeration effect&input is work done to make it)
In heat pump refrigeration effect will be more by giving energy as compared to refrigerator

Answer / pravin

For engine i.e heat engine the end result is termed as
output but for refrigrator/heat pump end result is not
output but the desired effect (heating or cooling) it
produces, so here comes the COP which is desired
refrigration effect/work required to produce that effect.

Answer / girish

Calculating COP we consider Heat Absorbed and While calculating Efficiency we take into account Heat Rejected.

what is the technology used in sap?

0 Answers   InFocus, Infosys,

---

function of the strainer in ic engine?

3 Answers   Castrol,

---

What is Spillback controller? Where is it used?

1 Answers  

---

what is the use of CW(Circulating water ,clarified water,cooling water),auxiliary cooling water(ACW),auxiliary raw cooling water(ARCW)in thermal power plant.plzz explain the different characteristics of these types of water.

0 Answers   NTPC,

---

I have applied for rrb ,for the post of JE (mechanical),So please send me the solved Question papers for the past four years RRB EXAM's as soon as posible.

1 Answers  

---

An machine is constructed to provide physical pleasure to a woman.It achieves 6 hp at 7600 rpm how can you use this engine to pleasure the girl without killing her?

3 Answers   Bhushan Power Steel, TATA,

---

Why start up vent is fully kept open when boiler is lighted up?

3 Answers   Isgec, Thermax,

---

1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

0 Answers   Bhel,

---

which purpose use in air intake system

0 Answers  

---

What is the melting temperature of the cng long tube fusible plug? And can I use lead solder Sn97Cu3 (Melting temp S/L 227-309 °C) Materials of tube : AISI 4130 Alloy steel

0 Answers  

---

could you tel me the kind of questions general asked by technical round about ERP.

2 Answers   HCL,

---

project,planning, equioment erraction &maint format. project,planning&scheduling,bar chart

0 Answers  

---