if drum level is low what is interlock? i mean we put interlock to fd fan or i

if drum level is low what is interlock? i mean we put
interlock to fd fan or id fan ?

Question Posted / santhu.janga

4 Answers
13914 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

if drum level is low what is interlock? i mean we put interlock to fd fan or id fan ?..

Answer / hansdas b.jaiswal

Drum level low its interlock with ID fan.If drum level is
low then ID fan will tripped.If ID fan tripped then PA fan
will tripped after PA fan tripped FD fan will tripped.

Is This Answer Correct ?

10 Yes

4 No

if drum level is low what is interlock? i mean we put interlock to fd fan or id fan ?..

Answer / nani babu

drum level interlock is fd fan ie drum level ismlow fd fan
tripped

Is This Answer Correct ?

11 Yes

7 No

if drum level is low what is interlock? i mean we put interlock to fd fan or id fan ?..

Answer / r.murugan

Dear santhu,
During normal boiler operation if drum level low (means drum pressure is high) during that time drum kevel controller will take care if not maintain that time further going level lowlow boiler will trip

Is This Answer Correct ?

5 Yes

2 No

if drum level is low what is interlock? i mean we put interlock to fd fan or id fan ?..

Answer / dilip jha

If drum level is low , firstly ID fan will trip then FD fan tripped then PA fan will Tripped.
This is the interlock of Drum Level Low.

Is This Answer Correct ?

2 Yes

1 No

Post New Answer

More Instrumentation Interview Questions

how in the 2 - wire transmitter, 24v supply and the 4ma signal gets in the same path?

1 Answers Yokogawa,

Why we use 3-15 psi air for control valve input?

2 Answers

You are looking at the RS-485-side of an RS-232/RS-485 converter and the power supply voltage for the converter is +5V. Under idle conditions (no transmission), and assuming you have enabled the RS-485 output: what would you expect at: (a) Output A measured against output B (b) Output A measured against ground (c) Output B measured against ground

1 Answers EIT,

what is written on orifice plate?

4 Answers

[ MITUTOYO / TESA / KUMAUN / MAHR / BRITOOL / TOHNICHY / DIATEST-GERMANY / IMADA / TECKLOK / SYLVAC /ADITYA=ACCURATE / BAKER/ CRYSTAL / FLUKE-RAYTEK ETC. 5.=SUPPLY= VERNIER CALIPERS / MICROMETERS / HEIGHTGAUGES / SLIPGAGE / BORE DIAL GAUGES / MEASURING PINS / TORQUE WRENCHES / GAUGES.. PLUGGAUGES / RINGGAUGES / SHORE A / D HARDNESS TESTERS / DIAL THICKNESS GAUGE / FEELER GAUGES / ELECTRONIC COMPARATORS WITH PROBES / DFTMETERS / SURFACE ROUGHNESS TESTERS / DIGITAL= COATING THICKNESS METERS / PROFILE PROJECTORS /.. WE ARE ALSO DEAL IN == DIGITAL TACHOMETERS / =MULTIMETERS! / VIBRATION METERS / MEGERS- INSULATION METERS / =TE! MPRATURE INDICATORS / SOUND-LEVEL METERS / ETC... =AGENCY- FLUKE- RAYTEK.. MECO....LUTRON...KYORITSU....RION

0 Answers

Difference HAZOP and HIRA

1 Answers

how can calibrate vacume trasmitter by HART COMMUNICATOR ?

3 Answers Bajaj, IMECO,

what is actual difference between pressure Transducer & Pressure Transmitter.

5 Answers

what is pico fuse? how this different rom othe fuses and how to locate it inside the card?

1 Answers

How a rtd work, and what volts/current goes to a RTD to measure the resistence?

1 Answers DVC,

in split range control system we are using two control valves,but we have only one positioner and one feed back link.so how we use this one feed back link for two control valves?

2 Answers

what is proportional & what is proportional band

1 Answers Nimir,

For more Instrumentation Interview Questions Click Here