Answer / jazz

the glycol serves as a calibrating fluid for your high and
low pressure impulse tubing of the dp transmitter. In this
way since glycol has a high boiling point and does not
evaporate easily, the calibration of your dp transmitter
remains the same as long as the level of glycol (the wet leg
compensating fluid)does not change. this serves also to
protect your transmitter's electronics from high temperature
since heat will be dissipated along the way on the impulse
tubing before reaching your transmitter..

Answer / mohammad iftikhar

Seal pots (sometime called condensate pots) are used
to allow a liquid seal between the instrument and flowing
gases such as steam. Their function is to keep the
liquid level constant in the impulse tubes. For example,
in boiler liquid level applications the high pressure (HP)
side of a differential pressure transmitter is connected
to the vapor space on top of the steam drum. Steam
condenses in the chamber or seal pot and fills the impuls
eline with condensate. The seal pot is located to
allow the condensate to drain back to the source thus
keeping the liquid level constant.

Answer / christian

it serve as protection to the instrument.it contain glycerin
or water vapor.with the principles of pascals law.external
pressure will be undiminished.

Answer / qamar abbas

if some meteriel come in impulse line he will block the
impulse line same like caustic sulphar thats why we fill
the glycol and also trasmiter superation and wet leg

Answer / suresh

The main purpose of filling Glycol is
(1) to avoid depositing of liquid with high density from the process which causes erratic reading. Glycol is having a density of more than 1.1 and normally liquids with less than this value will never settle down in the impulse line, giving a constant head which is suppressed or elevated to zero during the calibration.
(2)To transmit signals from process to transmitter where high viscous or solidifying products at ambient temperature is to be measured.Steam tracing can be avoided.

Answer / dsyedjaffer

Glycol used to portect electrions compounts ofthe transimeter.incase process variable is low density &pressure ie:white petrol
is easily evapourte inthe impulse line so we are used it.it is withstand high tem(1000 degree) so it used steam line

Answer / murali

it isolated the mix up of high pressure tapping & process
line fluid.and if any vapour presented in HP tapping fluid
it will remove it

what is modbus & what signals are taken through it

2 Answers  

How can I map a tank?  Tank 15m h and 42m dia. we just fixed radar type lit. its reading shows over range. Now its required mapping ?

1 Answers   CMC,

FOR CO/CO2/O2/NOX applications which of the following manufature is best? and what is the basic principle of gas analysers? ABB/YOKOGAWA/EMERSON/SIEMENS/TELEDYNE/THERMOFISHER

4 Answers  

How can we loop powered for a transmitter.How we can do wiring

1 Answers  

how to do dynolab wind speed sensor loop test, how to simulate value,i have simulate mA 4-20mA but not responding in DCS faceplate, please kindly advice me any one.

0 Answers  

Hi buddies! i am facing a problem and if someone could help me it will be an immense pleasure to me. we have compect logix PLC 1769 2L AO module to Heat @ 52 to 56 Deg C .So if anyone can do please help me out with this problem.I'll be highly grateful.

1 Answers   Cadila,

in natural gas indirect water bath heater,how to prevent the problem of backfire from firetube during ignition...becoz of this backfire performance of wbh is going low.

0 Answers  

What information needs for Control Valve "sizing"

1 Answers   Qatar Petroleums,

can anybody tel me how a vfd or any field instrument communicates/interface with plc/scada/cs.

0 Answers   Honeywell,

What is trim material . Why it is known as trim.

1 Answers   L&T, LNG,

Somebody ask me how many size of control valve what is mean of control valve size?

2 Answers  

How many types of sensor

0 Answers   Petro Rabigh,