Define "good" cooling tower water?

0 Answers  

---

we have 2 O2/Comb Analyzers Servomex Model 2700 in service for one of the furnaces in our chemical plant. It is giving High Temperature Alarm. Checked Temperature and found it to be 800 Deg C whereas Set Point is 700 Deg c. It is strange why is temperature not at SP. Also response is 23 % with 21 % Inst Air and with N2 reading is not coming down. please clarrify this issuses very urgent

1 Answers  

---

Explain the method adopted to minimize shell side pressure drop in a shell?

0 Answers  

---

Explain the steps required to design a vapor-liquid separator or flash drum?

0 Answers  

---

MASS TRANSFER - EXAMPLE 4.3 : According to Adolf Eugen Fick (1829 - 1901) : rate of diffusion v increases with less wall thickness t, increased area A and decreased molecular weight of a fluid M. The diffusion constant D decreased with increasing M. (a) By assuming v, t, dP, A, M and D changes proportionally of each other, find the equation of v as a function of t, dP, A and D. (b) The ratio of self diffusion constant D, at T = 273 K and P = 0.1 MPa, for gases B and C are 1.604 : 0.155. If only 2 gases exist in such a system : hydrogen and nitrogen, find the type of gas for B and C with reference to their molecular weights M. (c) By using the equation of kinetic energy 0.5 MV = constant where V = square of v, find the ratio of V for B and V for C, or V(B) / V(C), as a function of M(B) and M(C), where M(B) is molecular weight of B and M(C) the molecular weight of C : Graham's Law of Diffusion.

1 Answers  

---

Why whenever a reciprocating compressor is switched ON or OFF it is put into unloading mode?

0 Answers  

---

QUANTUM COMPUTING - EXAMPLE 32.10 : In quantum computing, the conversion of Control Not (CNOT) gate in two input quantum bit gate could be decribed as : | 00 > --> | 00 >, | 01 > --> | 01 >, | 10 > --> | 11 >, | 11 > --> | 10 >. If | P > = 0.707 ( | 01 > - | 11 > ), find the value of CNOT | P >.

1 Answers  

---

Question 36 - For a mixture of benzene (B), toluene (T) and xylene (X), the equation applies where x for B, T and X will sum up to 1. The equation of x for each component is x = (L / V + 1) (F) / (L / V + K). The data of F for each component are : 0.5 for B, 0.35 for T, 0.15 for X. The data of K for each component are : 1.98 for B, 0.76 for T, 0.24 for X. When x for B + x for T + x for X = 1, find the values of (a) L / V; (b) x for each component of B, T, X respectively. You may use Excel program - Data : What-If-Analysis for Goal Seek to perform the iterative calculations.

1 Answers  

---

How can one determine the particle size distribution for a given bulk solid?

0 Answers  

---

Explain how can you prevent bridging in a dilute phase pneumatic conveying system?

1 Answers  

---

ELECTRICAL TECHNOLOGY - EXAMPLE 16.2 : In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?

1 Answers  

---

We are having proplem with the persperation smell in ETT/ECHO room in our cardiac hospital.The 2 Ton of AC is not conditioning the environment. We have to use exhaust fan to through out of the room bad air. Could anyone suggest how to coup with this effectively using chemical engineering. Any permanent solution to neutralise the bad smell.The Air freshners are not doing enough instead making a bad odour.

0 Answers  

---