we touch other end of the tester supply, why do not get
shock?
Answers were Sorted based on User's Feedback
Answer / muthukumar
In other end we have the resistor for current limiting
| Is This Answer Correct ? | 32 Yes | 9 No |
Answer / kalolia alap r
in the tester rated 230v,and suppose resistance of tester in
megaohms,so the current will be less than 5 mA,it create no
hazard to human body,sowe don't get shock...
| Is This Answer Correct ? | 22 Yes | 0 No |
Answer / rajeev.p
The other end of the tester,supply came through a
resister.There for the voltage is reduced by resistor.
| Is This Answer Correct ? | 11 Yes | 4 No |
Answer / shashidhara
Rating of voltage is 230V only. The current is low enough not to hurt us and just enough to light up the bulb. But, the same tester can't be used to check higher voltages. We use only the voltmeters and other devices to check supply in higher voltages. If we use tester, we get shock at those high voltages.
| Is This Answer Correct ? | 2 Yes | 4 No |
Answer / yogesh raste
Since our body resistance is very high we do not expeince a
shock.
| Is This Answer Correct ? | 2 Yes | 42 No |
what is mean by NTPC?,why didn't electric shock in train?
Sir,In our company there are 3 caterpillar make(capacity:(1) 3.3KV,2.5MW(2)3.3KV,2.5MW & (3)3.3KV,1.9MW) & 1 deutz make (capacity:11KV,3.8MW)gas engines utilised,all are running in paralell. There are three transformer utilised,(1) 6.25MVA,3.3KV/22KV,Impedence voltage:6.7% used for two generator,both are 2.5MW(2)5.5MVA,3.3KV/22KV,Impedence voltage:7.2% used for one generator of 2.5MW & (3) 5.5MVA,11KV/22KV,Impedence voltage:7.8% used for one generator of 2.5MW.all generator breakers capacity of 1250Amps. Sir,I want the details of fault level calculation of generator,transformer individually & for whole system. If you require any information from me.feel free for contact me sir.pl.send the answer of my question as the earliest as possible.
Why Ferranti effect not occurs at full load?
Write a note on materials used as a fuse element.
Can a dc motor works as a dc generator. If yes , then how?
Q.1:What protection will be used on HT and LT side of 33/0.4 KV, MVA transformer. Indicate capacities of protective device to be used. Q.2:Which types of back-up protections are used in the power transformers? What do you understand by the term over travel in the relay? Q.3:How star and delta connected winding transformer are provided from earth fault
What is the basic difference between directional and non directional over current protection?
30 kVA and voltage 380/220VAC how to find out kA?
Why frame of the motor is specified?. If we mention KW and voltage level,automatically frame is decided or separately frame is compulsory to mention?.
in HVDC transmission system ,monopolar link has one conductor usually a negative polarity and use ground or sea return ?through negative polarity we could pass electricity or not yes means how it is possible
The normal highest generated voltage in India is a) 6.6KV b) 132KV c) 11KV
one electromagnet is called
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)