i want to know about for what reason we are using star delta starter? how it w

i want to know about for what reason we are using star
delta starter? how it works? what are the advantages?

Question Posted / ashish pandya

4 Answers
7423 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

i want to know about for what reason we are using star delta starter? how it works? what are the a..

Answer / prashant kaushik

Star Delta use for starting of motor as during starting
motor take high current so we can reduce it through using
star delta starter.

Is This Answer Correct ?

0 Yes

0 No

i want to know about for what reason we are using star delta starter? how it works? what are the a..

Answer / amit agrawal

star delta starter are used for controlling starting current. as we know, when we start any motor/pump then motor takes 6 times if rated current as there is no back emf ins tarting(speed zero).
If we apply star circuit then the voltage will be one third of delta circuit, in the same way current will be reduced.
This is the answer.
One more thing that all the HT(6.6KV) motors also be in star to control the starting current and to save the cost of insulation for both motor and connected cable.

Is This Answer Correct ?

0 Yes

0 No

i want to know about for what reason we are using star delta starter? how it works? what are the a..

Answer / kishor

starters are used for the purpose of to reduse the starting current...
in star-delta starter motor starts in star connection at this time motor voltage reduses than 1/root3...
there fore current is also reduse 1/root3...
and after some time motor is automatically convert to delta mode through timer....

Is This Answer Correct ?

0 Yes

0 No

i want to know about for what reason we are using star delta starter? how it works? what are the a..

Answer / prabhakar

Stard delta starters are to avoid accident it works with
contactors it save energy.

do you want to know what is star delta

the motor whih has dol connection will consum more current
and the motor which as star connection will consume less
corrent that is the reson we use motors and star delta
starters

Is This Answer Correct ?

0 Yes

8 No

Post New Answer

More Electrical Engineering Interview Questions

What should be value of Circuit breaker operating time and tripping time?

3 Answers

What is the direction of rotation of blades in a table fan and in a ceiling fan ?

11 Answers Power Grid,

TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2

0 Answers KSEB,

could any one explain me what power factor and where it is use ful

3 Answers

which type of harmonics minimum produce in 12 pulse rectiformer transformer? a)3rd b)5th c)7th d)11th

4 Answers Power Grid, Powerica,

iii) A shunt motor runs at 70 rad/sec from a 460V supply and takes in an armature current of 100A. Resistors of 2.52 ohms and 1.64 ohms are connected in series with the armature and in parallel with the armature respectively. The field excitation remains direct from the 460V supply but the generated torque is halved. Determine the new running speed. Neglect brush voltage drop. The armature resistance is 0.4 ohms. [15]

1 Answers

when ID fan will immediately stop through VFD what exactly cause and problem the ID fan

0 Answers

what is the range of thermal overload and over current. Answer should be in percentage of current.

0 Answers RMSI,

what is the value of voltage & current lightning during rainy season.

0 Answers

how the arcing is made in ac electric arc furnace? ( between the three electrodes in any sequences or between the electrode & the charge(steel))

1 Answers

What is the Operating Powerfactor of UPS??? Why??

3 Answers

Why we use DC for charging of Batteries??Why not AC Supply???

6 Answers Emerson, Infosys,

For more Electrical Engineering Interview Questions Click Here