i have a bar of 36 dia in column, what is the lap length?

Categories >> Engineering >> Civil Engineering
Suggest New Category

Question Posted / anil kumar vaddi

12 Answers
23611 Views
RMC, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

i have a bar of 36 dia in column, what is the lap length?..

Answer / anil

as per indiaqn standards the bars above 32mm dia bars are
to be welded not lapped. its a twisting questions in
interviews

Is This Answer Correct ?

37 Yes

0 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / manjunath.g.m

50dia of the bar

Is This Answer Correct ?

16 Yes

11 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / kamesh

50x dia of rod
so 50x36=1800mm

Is This Answer Correct ?

10 Yes

6 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / laxman nayak

Sume time we will used cupler joint

Is This Answer Correct ?

1 Yes

0 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / ashok yadav

Lap length is depends on various factors such as grade of
concrete used, load on the structures and economical
criteria.

Is This Answer Correct ?

0 Yes

1 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / xxx

depending upon the design..........40-63d

Is This Answer Correct ?

3 Yes

5 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / irwin

Since the 36 mm dia bar is subject to compression, hence the the formula for the required lap is L=37(d)
where;

d=36

L=37(36)
L=1,332 (minimumn required lap for compression)

Is This Answer Correct ?

0 Yes

2 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / sjtbehera

yes 50 dia of bars in thumb rule. but when you are going to
calculated it is diffrence in compression and tension zone.

Is This Answer Correct ?

3 Yes

6 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / mahendra mohan srivastava

Lap length will 50 d here d is dia of the bar.
and anchroge length will 58d. after 25d lap length will
joint through welding joint.

Is This Answer Correct ?

1 Yes

4 No

i have a bar of 36 dia in column, what is the lap length?..

Answer / sudhir patil

Actually its depend upon the design & grade of concrete.Its
normal practice to take 50 times of the diameter of steel
hence for 36 mm dia bar it should be taken 1800 mm.

Is This Answer Correct ?

4 Yes

7 No

Post New Answer

More Civil Engineering Interview Questions

What should be the min.compressive strength of cc cube after 7 days testing and 28 days testing for M25 design mix conc.?pl give idea with relavant is code

9 Answers IP Infra Power,

how to decide cement quantity in 1 m3 concrete

3 Answers L&T, Rich Link,

How to come 1.54 from dry to wet concrete?

0 Answers ASZ, L&T,

what is tacheometry?

3 Answers NBCC,

how i can tak Quantity of mortar in block work

0 Answers DLF, LiveCon,

In the design of bridge arguments what considerations should be made to select the orientation of the wing walls?

0 Answers

how much the volume of one packet cement ?

6 Answers

In 120 m high RCC Chimney shell construction how we can calculate the inner and outer dia of shell at every +1 m level as this shell is inclined from bottom to top.

4 Answers

Why provide strripus in a column minimum and maximum spacing.

1 Answers

How Many Brick in One Cubic Meter.

9 Answers TUV,

How do we calculate the weight of aggregates, sand and cement M 25 design mixfor 1 cum

1 Answers

what is a coupler and where do u use it ?

1 Answers ITC Infotech,

For more Civil Engineering Interview Questions Click Here