Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
WHAT ARE EARTH MOVING M/CS? WHAT IS BATCHING PLANT? WHAT IS HYDRAULIC JUMP? WHAT IS TIPPER (EARTH MOVING M/C)?
2741DRAW REFRIGERATION CYCLE? WHICH REFRIGERANT USED IN IDUSTRY & HOME? EOT CRANES SPEED ? WHAT IS KOM ? TELLL ME ABOUT YOU? WHAT WAS YOUR FAVORITE SUBJECT?
3 5779why some time Railway Fan not Rotate,But after a small rotation by human then it rotate normally? Why?
4 7275which kind of force act when the piston slides inside the cylinder?and how to calculate that force or stress theoritically.
4 6415what are the parameters are selected while manufacturing a single cylinder block?what are the different kind of test is conducted on it so that it can withstand with all those condition which required to run the engine efficiently.which force is act when piston slide inside the cylinder.
2022what are the parameters are selected while manufacturing a single cylinder block?what are the different kind of test is conducted on it so that it can withstand with all those condition which required to run the engine efficiently.which force is act when piston slide inside the cylinder.
Emco,
2093what is the relation between reactive power and power factor for the what is the limit of reactive power and power factor
2103Whot is the difference between MCB and MCCB.Whot is the selection critearea for MCCB and MCB for 63 Amp.
5 9525For refrigerators the motor current is raised beyond its rating on both conditions when the voltage of the system is more(say 270v) than the rated voltage(220v) as well as when the voltage of system is less(say 160v) than normal voltageof 220v, why explain?
19739*9 1:4:8 ratio using how to calculate the material for 40mm aggregate ,cement &sand please tell me answer
5 40715length of 4 core cable 95mm from substation LV VFD panel to Motor at field approximately 150 meter. Motor stop and power has been isolated from LV MCC ( Substation )to disconnect Motor for services. After Motor completed service propose to reinstall and reconnect Motor Cable, found earth cable sparkling during touching at metal / motor body. Inspect by clamp meter found earth cable have current flow AC 1-2amps and all earth cable at MCC LV also have current flow as same value. why it is happen?
2 6105
what is the main fuction of OSPF in a internetwork? how does work of same network?
in shunt clippers why a resistor is used in sereis with the input
Can you tell me any three mineral fibers?
What are different types of valves?
I have file with input as below : Name Value Rohan 12,13,14 Rohit 1,2,3 Output should be : Rohan 12 Rohan 13 Rohan 14 Here how will the normalize component work? Thanks
Explain how can I evaluate the thermal relief requirements for double block-in of 98% sulfuric acid?
* ** *12* *123* *1234* *12345* *123456* ********
What is difference between slip rings and carbon burushes?
what is Quantity of stone and sand required for one cubic meter of stone work (UCR)
1 “earthing” for bonding of equipment and circuits to common plant earth electrode potential, 2 “protective earthing (PE)” when this bonding is required for personal safety provisions 3 “grounding” for interference suppressing bonding of screens, sys-tems with ground level 4. low-impedance earthing ? 5.primary earthing system and secondary earthing system what is that? 6.earthing electrode or mesh net earthing electrode ? very confusing , simple but very informative help required ? i will be very very thankful to you guys.
The height to which the liquid in a tank to be maintained for a certain constant velocity?
Is electro plating what type of load whether resistive, inductive or capacitive loads
How can we findout the maximum efficiancy of Transformer? At which load?
armature is that part in which current is induced since in dc motor we supply current to the conductor so why we call it armature?
Tell me what if you have a garment or fabric that is half or less polyester and the other portion a natural fiber (like cotton), you can try using the reactive dyes?
