Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379) when the instrument tapping on pipe line is located below and transmitter is located above the tapping point for liquid service transmitter, what should we do, is there any additional drain valve is required??
2185when the instrument tapping on pipe line is located below and transmitter is located above the tapping point for liquid service transmitter, what should we do, is there any additional drain valve is required??
2 159861) what is the difference between development length & overlap length ? 2) why extras are provided at top and bootom in a beam of slab? 3) why stirrups are provided at 0.3l at supports and 0.4l at center? 4) is column a compression memeber if yes how & beam is which type of memeber?
4 28796In Round type three phase transformer why the LV side is inner part and HV outer part in the design of transformer? why they cant be opposite?
2 7182
We have given to 3phase supply to ups system & how can coming netural
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
Why GRR starts from 60% of motor speed why not less than 60%?
Hi i am riyaz ahmed . i got rejected for first time and i nedd to apply for next time and can i apply in 1 or 2 week . and wt abt my sevies fee ? i should make a new once shill i go with the same and wt docement i should change can u plz help me out and my mail it is royalriyaz@gmail.com
Differentiate between 304 and 316 grades of steel?
Write a program using string fuctions that accepts a price of an item and display its coded value. The base of the key is: X c o m p u t e r s 0 1 2 3 4 5 6 7 8 9
why we use low and high radio band in m/w link at both end
which type of motor is used in automatic swing gate
Explain the operation of 3φ bridge inverter for 1800 degree mode of operation with aid of relevant phase and line voltage waveforms?
Mention some of the specialized crushing methods?
What is enclosed seam?
can u tell me placement peoceduers and placemnt format of hpcl.
1. Design a counter which counts 0, 4, 8, 2, 6, and repeats using: 1.a using JK flip flops 1.b using T flip flops 1.c using D flip flops
What is the principle of HIGH SPEED DIRECT DRIVE MOTOR ?
what are the challenges of being a team leader and a supervisor?