Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
what's the difference between ATS and AMF...??pls answer me in detail with its working principle and construction also..
3 23019a concrete mix 1 2 4 by volume with water cement ratio as .6 by weight if moisture content in F.A is 6% with 20% BULKING AND IN C.A 1.5% by volume. find quantities of different materials required for one bag of cement
2114extremely urgent please, why a fuse is used before voltmeter but not with a ammeter connected to a CT(current transformer),thanks in anticipation.
4 10135We have drive feeding an output contactor for a 5000 hp motor @ 5kV application. The motor FLA is 629amps x 1.25% service factor = 786.25 amps The cable that we current have in place between the drive and the output contactor is 350kcmil- MV-105 (parallel cables). Per the NEC table 310.60 (C) (69). This show the cable ampacity is at 615 amps per cable for a rating of 1230 amps. We have derated the cable for the cable tray and the multiple cables application and our calculations show that after the correction factor factor we are at 922amps. 1230 amps x .75% correction factor factor = 922.5 amps. The customer is driving us to then use another safety factor of .25% off of the already derated cable. Can you please provide a longhand calculation for your solution on this application?
2150The horizontal distance between parallel main reinforcements in RC slab shall not be more than
BEL, BSL, L&T, Mrkr Constructions,
1 8997watt meter have 4 terminals what there name??? and what theses 4 terminals indicates ?? and why 2 terminals are short circuited??
1 6361why most of the DP transmitters using maximum range as 0-2500mmwc?why not 1000 2000 3000 4000mmwc
2 8327How we will check whether the proximity, which we have is either NPN or PNP, if no data sheet or manual or any details is available to us ???
1 6707
Do the design & fittings depend on the type of the vehicle engine? Why is petrol used for engines only & vice versa.
What is additive color?
Advantages of using generator circuit breaker (GCB) scheme in a power station ?
What is the main purpose of an airspeed indicator in an aircraft?
Preparation before arriving port?
what is the calculation involved to design the heater to heat 10KL of water in temperature control unit?
What is the importance of peak inverse voltage?
What are the advantages and disadvantages of using gear pumps?
7. Orange LED on RRI card is glowing – what is the indication?
how can get electrical "c" licence.i am complited in DEEE.PASSING YEAR OF 1993.WORKING IN PVT COCERN LT LINE.PLEASE ADVISE ME .CELL NO 9994786021
List out the different frequency domain specifications?
I am having 5 nos. ceiling fans in my home. if i switch on all fan at full speed say 5 , so Will my meter reading be runing fast ? OR if I keep all fans on very low speed, say 1, so meter reading will runing slowly. or it does not make any difference whether low or high. reading will remain same?
Why opamp called operational amplifier?
where i can get soil testing report for construction in aurangabad.
sir, pls mail me the previous question papers of RRB Junior Engineer Gr-II Drawing
