Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
In a power system we know that if the generated power is less than the load then the frequency of the system is decreases.So does this mean that total required load is delivered at alower frequency?
1 3442what is The difference between national electrical code and I.S.Code (electrical) and what is the value of NEC in electrical engineering field
2086How much kilogram of binding wire required for fabricate one Metric ton of reinforcing steel
7 17002An 11kv system consisting of an underground cable to a sub station about 300 meters away was shut down for about 10 hrs. On energising, it tripped off on earth fault about 10---20 mins later 6 times but since than it is not tripping.its already 3 weeks now. The SPAJ was found to be fine. what could be the cause.No test had been done to determine the cause of the trippings till now because of demand.
2 4761The process variables that need to monitored and controlled are ________, ________, _________ and
1 3721A length of steel pipe is used to carry sea water to a desalination plant. An adequate corrosion allowance must be specified and indicated in the piping specification, which affects the _________________________ of the pipe
2298Describe the typical instrumentation used in monitoring the performance of a shell and tube heat exchanger.
2129The pressure class rating (such as 150 lb, 300 lb, etc.) of a line appears in the form of ________________ in the Line Number (or Line Designation) on a P&ID
1 4714The document / drawing that is primarily used in depicting the “Bill of Materials (BOM)” of piping system is the
2 4984A flange is used for instrument connection for a system with a design temperature of 316C (600F) and a design pressure of 1000 kPa (145 psi). What is the class rating of the flange to be used for this application? Explain your answer
2744How much steam required for 1MW power production form 30 bar G super heated steam(350 C), outlet of turbine 4.5 bar
2225
i have one air blow heater , coiled heater is in side hollow ceramic tube and passing the air and other end hot air is going out, to control the hot air where i should fix up a THERMOCOUPLE on the heater or on the out let of hot air terminal which is the best way
basic connection and principle of axial shift sensor n differential sensors in tubine describes n draw......
What is the difference between E1T1 Card & RRI & FIU.
I want to preparation of mppsc interview
which are the five general EMI(electromagnetic interference) testings conducted on any system?
Explain what is a differential amplifier?
Sir, My doubt on cable sizing calculation, Load:74 KW calculated cable 1 run 50mm2. Now client asking us to reduce cable size by increasing runs. Sir, My question now when my mind strikes with 2 options 1) Divide load 74/2 = 36 and calculate cable for 36+36 making it 2 runs or 2) Simply i can divide 50mm2 /2 ie. 2 runs of 25mm2 Please suggest me sir
What is the difference between power amplifier and voltage amplifier?
Explain the fashion accessories?
How to handle production department ?
what is function of SCADA , and how is it work, explain with difination
can u please tell me how to calculate the concrete quantity for a under reamed pile? r=300mm,depth=3m for a cylinder and for bulb l=.750mm,width=.525
how was your last weekend.
Explain how to clean LO
Scott connection is used for A 3-phase to 2-phase conversion B to achieve higher effciency C to save copper D to reduce harmonics
