Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


How can i check a relay good or not?

Answers were Sorted based on User's Feedback



How can i check a relay good or not?..

Answer / abdul ghouse

A relay is an electrically operated switch. Many relays use
an electromagnet to operate a switching mechanism
mechanically.

commonly there are 4 legged (pins) for relay. You can check
the mechanical switch by Ohm meter (multi meter) similar
like Elec switch testing. ON - OFF low and high resistance
it should show then it should OK or else its defective.

the other part of relay is Elec winding part can be tested
by continuity check

Is This Answer Correct ?    1 Yes 2 No

How can i check a relay good or not?..

Answer / k.prakashchandra

By simulation

Is This Answer Correct ?    0 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

why ct ratio always rated 5.

1 Answers  


in which direction real power and reactive power flow and why???????

3 Answers  


can a synchronous motor be made to rotate in a clockwise direction ?

1 Answers  


1000 W bulb takes 4.16 Amps at 240 volt then what will be the KWH & if i am using 1000 W bulb at 180 Volt the amps will be 5.55 then what will be KWH????????????????

2 Answers  


inductance and capacitance may result in periodic reversals of the direction of energy flow,how???

1 Answers  






how to find diesel consumption of 600kva DG per hours????

1 Answers  


We have got the HT connection of 1000 KVA in which we have installed a seprate APFC panel at the PCC end & seprate KWH meter is installed. My question is that does the KWH reading shown in the meter is a part of the Consumption ???? ( approx 500 units is shown)

1 Answers  


what is the power factor?please tell me uses.

5 Answers   NTPC,


What would be the ratio of a Delta-Wye tranformer having 48000 volts phase to phase on the primary and 4160 volts phase to phase on the secondary?

5 Answers  


I have tow 200 KVA UPS, both are in parallel mode.My question is that, both are running on battery when power fail, if one of them fail (Eg rectifire fails or some other reason), at thet time reverse power will come to faild ups if it comes then it will harm to failed ups or not? if not then how it protects to faied ups????????????????

1 Answers  


What are difference between earthing switch and earthing truck ? What is the operation philoshopy of earthing truck ? Wht are the component of earthing truck ?

2 Answers   Reliance,


What is the difference between a Vacuum Circuit Breaker and a Load Break Switch?

7 Answers  






Categories
  • Civil Engineering Interview Questions Civil Engineering (5075)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4444)
  • Electrical Engineering Interview Questions Electrical Engineering (16600)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2987)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (170)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1377)