As system administrator, you type "debug ipx sap" and receive the following lines as part of the IOS response: type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops What does "0x4" signify? A. That is a Get Nearest Server response. B. That it is a General query. C. That it is a General response. D. That it is a Get Nearest Server request.
2 9990To monitor IP igrp traffic, you can use "debug IP igrp transaction" or "debug IP igrp events". How do you display information about IPX routing update packets? A. debug routing B. debug ipx transaction C. debug ipx routing activity D. debug ipx events
2 12033To monitor ipx traffic on a network, what command would you use? A. debug ipx transaction B. show ipx traffic C. show ipx events D. display ipx traffic
3 12515What command would you use to find out the names of Novell servers on a network? A. show ipx servers B. show ipx hosts C. show ipx sap D. show ipx nodes.
1 7639The "ipx delay number" command will allow an administrator to change the default settings. What are the default settings? A. For LAN interfaces, one tick; for WAN interfaces, six ticks B. For LAN interfaces, six ticks; for WAN interfaces, one tick C. For LAN interfaces, zero ticks; for WAN interfaces, five ticks D. For LAN interfaces, five ticks; for WAN interfaces, zero Ticks
1 10080As a system administrator, you need to set up one Ethernet interface on the Cisco router to allow for both sap and Novell-ether encapsulations. Which set of commands will accomplish this? A. interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx network 6c B. interface ethernet 0 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0 ipx encapsulation sap ipx network 6c C. interface ethernet 0.1 ipx encapsulation Novell-ether interface ethernet 0.2 ipx encapsulation sap D. interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c
1 8987What does the "IPX maximum-paths 2" command accomplish? A. It enables load sharing on 2 paths if the paths are equal metric paths. B. It sets up routing to go to network 2. C. It is the default for Cisco IPX load sharing. D. It enables load sharing on 2 paths if the paths are unequal metric paths.
3 9841You want to enable both arpa and snap encapsulation on one router interface. How do you do this? A. The interface can handle multiple encapsulation types with no extra configuration. B. Assign two network numbers, one for each encapsulation type. C. Enable Novell-ether to run multiple encapsulation types. D. Both arpa and snap are enabled by default so you don't have to configure anything.
2 14332To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks? A. Each router builds its own SAP table and forwards that every 60 seconds. B. Each router assigns a service number and broadcasts that. C. SAPs aren't necessary with Cisco routers. D. Cisco routers filter out all SAPs.
1 7963Novell's implementation of RIP updates routing tables every ____ seconds. A. 60 B. 90 C. 10 D. 30
1 11541In Novell's use of RIP, there are two metrics used to make routing decisions. Select the two metrics. A. Ticks. B. Hops C. Loops D. Counts
3 10785What is the Cisco name for the encapsulation type used on a serial interface? A. HDLC B. SDLC C. SAP D. SNAP
HCL,
3 15035"arpa" is used by the Cisco IOS for which encapsulation types? A. Ethernet_II B. Ethernet_802.3 C. Ethernet_802.2 D. Ethernet_SNAP
3 44721"snap" is used by the Cisco IOS for which encapsulation types? A. Ethernet_SNAP B. Token-Ring_SNAP C. FDDI_SNAP D. Novell-SNAP E. Novell-FDDI.
ZTR,
1 9042
After how long eigrp protocol advertise its routing table?
Can you explain voluntary and compulsory tunnels?
Name the 2 protocols are in wan technology?
Which defined peer ip address an local subnet belong to crete?
Explain the benefits of VLANs.
Explain on which interface we always apply access-list?
I simulate ten routers r1 to r10 straightly. I want I can ping from the loop of r1 to loop of r10, but I want I cant ping r1 and r10 from inside routers.?
Suppose a Switch interface went in error-dis mode what you will do for Troubleshooting List all Possibilities
What is the mesh network?
Define topology?
What is the difference between switch, routers, and hub?
What is the name of best path in eigrp protocol?
If bandwidth will increase what will happen?
1350 Value in which type of access-list?
Can you explain the broader steps of how L2F establishes the tunnel?