The "ipx delay number" command will allow an administrator to

change the default settings. What are the default settings?

A. For LAN interfaces, one tick; for WAN interfaces, six

ticks

B. For LAN interfaces, six ticks; for WAN interfaces, one

tick

C. For LAN interfaces, zero ticks; for WAN interfaces, five

ticks

D. For LAN interfaces, five ticks; for WAN interfaces, zero

Ticks






The "ipx delay number" command will allow an administrator to change the default settin..

Answer / guest

Answer: A

The default is--for LAN interfaces, one tick;

for WAN interfaces, six ticks

Is This Answer Correct ?    6 Yes 0 No

Post New Answer




More CCNA Interview Questions

what is the need og jitu(config)#ip helper address <ip address> can any one exaplain it briefly specially shain i am looking towards you.Becoz you are the only one who can solve my that problem not even jitendera sinha

4 Answers  


Choose three reasons why the networking industry uses a layered model: A.) It facilitates systematic troubleshooting B.) It allows changes in one layer to occur without changing other layers C.) It allows changes to occur in all layers when changing one protocol D.) It clarifies how to do it rather than what general function to be done E.) It clarifies what general function is to be done rather than how to do it

1 Answers  


Identify 3 characteristics of switches? A.) Increase available bandwidth B.) Decrease broadcast traffic C.) Support full duplex in a multipoint topology D.) Make fowarding decision using MAC address E.) Create collision domains

1 Answers  


What will happen in OSPF, While a new highet priority DR joining in already running area.That area already having DR and BDR.

2 Answers   HCL,


Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0

0 Answers  






Identify the command to configure a description on an interface? A.) Router> description Finance department B.) Router(config)# description Finance department C.) Router(config-if)# description Finance department D.) Router# description Finance department

1 Answers  


Which layer is responsible for framing? A.) Application B.) Data Link C.) Physical D.) Network E.) Transport

3 Answers  


Ping uses which Internet layer protocol? A.) RARP B.) ICMP C.) ARP D.) FTP

4 Answers  


Why is network segmentation a good idea when managing a large network?

0 Answers  


To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks? A. Each router builds its own SAP table and forwards that every 60 seconds. B. Each router assigns a service number and broadcasts that. C. SAPs aren't necessary with Cisco routers. D. Cisco routers filter out all SAPs.

1 Answers  


Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay

1 Answers  


(1)what is "rtp" and how it work, (2)what is diffrence between igrp and eigrp (3)the slection prcedure of dr and bdr is depend open (4)why frame really is called nbma (5)what is ppp (6) what is diffrence b/w tcp and udp (7) how can we implement ospf protocall on any router (8)whta is as nomber (9)what is AD value (10)what is the broadcast id,n/w id and number of vallid host of the 255.255.255.128/25 195.168.10.10/25 (11) what is stub network (12) what is contigues n/w (13)on which type of router we can implement default routing (14)what is diffrence b/w hub switch;switch router, (15)what is v lan (16)what is the diffrence b/w link sate protocal and distance vector protocall (17)what is synchoransh mode of data transfer and asynchronash mode of data transfer (18) question on lab, belive me frnds there are 20 questions and 5 questions on lab implimentaion.around 1.1/2 hour i was in interview room and after givieng 17 right answera and 4 in lab i got slected try to give answer if any difficulty or any prob plz email me on jitenderasinha.it@gmail.com if any one of you havae boson netsim plz also intimate me

4 Answers  






Categories