"arpa" is used by the Cisco IOS for which encapsulation


A. Ethernet_II

B. Ethernet_802.3

C. Ethernet_802.2

D. Ethernet_SNAP

Answers were Sorted based on User's Feedback

"arpa" is used by the Cisco IOS for which encapsulation types? A. Ethernet_II B. ..

Answer / guest

Answer: A

Novell's IPX and Cisco's IOS name their

protocols differently. Cisco uses sap for Ethernet_802.2,

Token-Ring, and Novell's FDDI_802.2. Cisco uses snap for

Ethernet_SNAP, Token-Ring_SNAP, and FDDI_SNAP. Cisco uses

arpa for Ethernet_II and, finally the default is

Novell-ether for Novell's Ethernet_802.3.

Is This Answer Correct ?    43 Yes 6 No

"arpa" is used by the Cisco IOS for which encapsulation types? A. Ethernet_II B. ..

Answer / sachin


Is This Answer Correct ?    26 Yes 9 No

"arpa" is used by the Cisco IOS for which encapsulation types? A. Ethernet_II B. ..

Answer / rafael maita

The type can be: ARPA, SAP or SNAP. Specifying ARPA
(default) signifies that you want to use the standard
Ethernet version 2.0 encapsulation; SAP – IEEE 802.3
encapsulation; SNAP – IEEE 802.2 encapsulation. Mostly you
will use ARPA encapsulation. SAP or SNAP ones would be in a
native Novell NetWare IPX network.

Is This Answer Correct ?    11 Yes 1 No

Post New Answer

More CCNA Interview Questions

What is difference between static and dynamic routing?

0 Answers  

what is bgp i have ansered all of them except mpls while i am working on it but i donot have threotical concepts on it the told me that they are keeping me on hold let try urs knowledge all the best

1 Answers  

Which three of the following are true statements about connection-oriented sessions? A.) The segments delivered are acknowledged back to the sender upon their reception B.) Any segments not acknowledged are retransmitted by the receiver C.) A manageable data flow is maintained in order to avoid congestion, overloading and loss of any data D.) Segments are sequenced back into their proper order upon arrival at their destination

3 Answers  

Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp

2 Answers  

Which command switches from User mode to Privileged mode? A.) login B.) privilege C.) admin D.) enable E.) enter F.) root

5 Answers  

What is the checksum?

0 Answers  

How do you set the encapsulation type to PPP for an interface? A.) encap ppp B.) ppp encapsulation C.) encapsulation ppp D.) encapsulation ppp enable E.) ppp enable encapsulation

2 Answers  

What does a metric of 16 hops represent when using RIP? A.) Number of hops to the destination B.) Destination unreachable C.) Number of routers D.) Bandwidth

2 Answers   IBM,

Identify the true statement regarding subnetting? A.) Allows for more host address B.) Borrow bits from the network portion of the address C.) Allows for unlimited number of networks D.) Borrow bits from the host portion of the address

1 Answers  

What does the term "attenuation" mean in data communication? 1 loss of signal strength as distance increases 2 time for a signal to reach its destination 3 leakage of signals from one cable pair to another 4 strengthening of a signal by a networking device

3 Answers  

Which of the following will apply IPX sap access list 1010 for incoming traffic, assume you are at the interface configuration? A.) ipx input-sap-filter 1010 in B.) ipx input-sap-filter 1010 C.) ipx access-group 1010 in D.) ipx access-list 1010 in

1 Answers  

Your network uses a Class C address of You must now split up the network into separate shores to handle multiple buildings separated by routers. Which two steps must you take to determine the proper shored mask for your networks? (Choose two) A. determine the number of seperate networks required B. determine how many devices will require DHCP addressing C. determine the maximum number of hosts that will be on each shored D. determine the miniumum number of hosts that will be on each shored E. determine which router will be the IP default gateway for each shored

1 Answers