Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual
1 4048Identify the command that disables name-to-address translation? A.) Router(config-dns)# no ip domain-lookup B.) Router(config)# no address translation C.) Router(config)# no ip domain-lookup D.) Router(config)# ip domain-lookup
1 4261What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface
1 5801Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config
1 4464Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco
1 4404Identify the effect of Ctrl-Z? A.) Exits back to privileged exec mode B.) Disconnect from the router C.) Abort the ping operation D.) Exits privileged exec mode
3 6142Given an IPX network with redundant paths, what command will configure load balancing? A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx load-share
2 5229Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
3 6588Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1
2 5278Identify the command to view the configuration-register value? A.) show register B.) display config-register C.) show config D.) show version
1 5009Identify the 2 commands that save the running-config to a TFTP server? A.) write running tftp B.) copy running network C.) copy running tftp D.) write network
3 5500Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode
2 5454How do you disable CDP on the entire Router? A.) Router#no cdp run B.) Rotuer(config-if)# no cdp enable C.) Router(config)# no cdp enable D.) Router(config)# no cdp run
1 4421What command can be used to test IPX connectivity? A.) Ping 2e.000.0045.8923 B.) Ping 192.168.100.1 C.) Ping ipx 2e.0000.0045.8923 D.) Ipx ping 2e.0000.0045.8923
4 11731Identify the 2 commands that display the clock rate configured on the serial0 interface? A.) show serial0 B.) show interface serial0 C.) show clock rate serial 0 D.) show controllers serial 0 E.) show running-config
5 9972
When configuring a router utilizing both physical and logical interfaces, what factor must be considered in determining the OSPF router ID?
What are segments?
What are the ranges for the private ips?
What is a Window in networking terms?
What is the frame relay, in which layer it comes?
How do areas benefit a link state inter network?
What is the difference between arp and rarp?
What purpose does aging serve in a link state protocol?
Differentiate Logical Topology from Physical Topology
Explain why UDP is lease favored when compared to TCP?
what are the different symmetric algorithms?
What are the different types of cables that are used in routing?
If line down and protocol also down; in this case which layer move problem?
Explain the terms unicast, multicast, broadcast.
What is cam?
