Answer / shahulsnfa

all the above is not seems to be correct.. the real thing
is in star IL=Ip so we are going for star at the time of
starting. after the machine attains rated speed we are
changing into delta becuase the machine cannot develop
rated TORQUE of the motor in star but it can develop in
delta since in delta VL=VP. that's why its changed to delta
instead of running in star. V is directly proportional to
flux is inturn proportional to torque.

Answer / madhav agrwal

When a delta motor is connected in star, the voltage across
the windings is reduced by the square root of three
resulting in reduced flux in the iron, this will reduce the
magnetizing current, and will also reduce the torque
capacity of the motor

Answer / silamparasan p.

Because the voltage in star connection is Vph=VL/square
root of three.
But in delta connection Vph=VL.
So in star connection is only for starting a motor.
But to run a motor through a delta winding. Becaus then
only full voltage given to motor and it will run in full
speed.

Answer / rajendran

The type of connection in which the motor is running
continiously depends upon its design and the type of
application it is used...

there are motors designed for continious star opearation...

But the basic thing is star is preferred for starting and
delta is preferred for runnnig owing to design as well as
economic feasibilities...

Answer / maged

Simple 3 phase motors can be connected in either STAR or
DELTA.
In star the maximum power is reduced but the starting
current is lower than for Delta
In Delta the motor gives maximum power but the starting
current is often too high and the overload trips out.
To overcome this a star/delta starter is fitted
All 6 wires from the motor windings are connected to the
starter and the starter functions are as follows :-

When start button is pressed the motor is automatically
connected in star and the start current is acceptable. At
the same time a timer is initiated and after a
predetermined time the starter automatically changes from
star connection to delta. The motor now runs in Delta until
switched off.

This is a fully automatic starter, many years ago manual
changeover star/delta starters were more common.

Answer / shaji samuel

Motor can be connected in delta as well as star.

In delta connection the maximum power that motor can give
is motor rating.ex 15 kw motor 15kw power.

In star connection the maximum power motor can give is
(motor KW * 1/3). Now the motor is derated.

Also note that if your motor 50% only loaded then the motor
winding can be connected in star instead of delta. This
will give you power saving. Also take care that always load
on motor is less than 50% or else motor winding will get
burnt. For more clarification mail me on
shajisame@gmail.com

Answer / ramasamy

Motor running with star or delta depends upon the design,the same is given in the name plate.The reason for most of the motors are in delta is to limit the starting current by turn ON in star connection & than converting to delta connection to get the rated speed & torque. Where as it is not possible if the motor design is star. But now we get more of star connection design motor which are VFD & soft starter application.

Answer / samir vyas

Its a matter of torque which is low in star because of reduced voltage at
winding and at designed load star connected motor get stopped due to
insufficient torque. More you have to see motor characteristic at diff.
Stage

Answer / dhanu

speed is depends on frequency and no. of poles.

Answer / a.venkatswami

motor running in delta it can be in star beacuse star
connected motor has taken voltage root three times and
current high that the cost is high threrfore motor runngin
in delta but in industres star motor connection also
working its motor rating low kw.

why can tv operate at low voltage??

2 Answers  

How loading get increased in generator not the speed, while we increasing steam to turbine.

2 Answers  

11 kv metering is done in my factory.Meter show PF 1.000 but kvarh lag&lead show 24&94 respectively & Avg.PF is .956 .? is what i do for inproove my PF to 1.000

3 Answers  

any earth foult trip the relay but in welding time not trip by earth foult

0 Answers   Power Grid, Siemens,

hi pal, i am vengatesh from tamilnadu(chidambaram),i have called for the written test for the post of jr executive(ELECTRICAL) of AAI ,I dont know about the question paper pattern,so any kindly help me to face the examination,post me the model question papers and some tips to write my examination to (vengi.annadurai@gmail.com)

0 Answers  

In a Circuit how the MCB and Fuse ratings are calculated. And shall the fuse follws the MCB or it is otherwise?

16 Answers   Emerson, HCL, Thirumalai Chemicals,

Define ohm’s law for a.c (alternating current)?

0 Answers  

Is there any difference between load based power plant and coal based power plant?

1 Answers  

when generator of a power plant is not connected to grid , by increasing the mechanical torque speed of rotor increases but when it's connected to load instead of increase in speed current increases , why?

1 Answers  

what is the safety of ACB & VCB and how can this work and how can the service the ACB & VCB parts name with picture

21 Answers   ABB, ACB, Bharti, Claris Lifesciences, Honda, L&T, RotoPower, Sterling Wilson, Wipro,

What is the phase relationship between the primary and secondary voltages of a transformer?

0 Answers  

please send me jindal previous aptitude and technical question and answer.my email id is deep_raj@live.com

0 Answers