Answer / manikandan

actually in transmission line HT and LT. high tension , low
tension . in transformer high voltage and low voltage.

Answer / sridhar

High tension and low tension, high voltage and low voltage

Answer / arun kumar

whch TR ARE USE IN HT LINE LIKE 33 ,11, 162 ,66 KV LNE ARE
CALLED HT TR AND WHICH TR USE TO CONVERT HIGH VOLTAGE INTO
LOW VOLTAGE LIKE 440V , 220V ARE CALLED LT TR

Answer / affendi

PUB supply to a building is known as HT or LT?

Answer / md ghouse adil meeran

We often come across the terms HT, LT, HV & LV in electric power systems and devices.
HT = High Tension starts from 3kv
LT = Low Tension
HV = High Voltage (almost like HT, usaully 1000V also calls High Voltage)
LV = Low Voltage (almost like LT)
these abrivations use all over the world for respective voltages.

Answer / shamsudeen

usually the power cables are used at the high voltage side
called as High Tension side. similarly on low voltage side
called as Low tension.
But in a transformer HT stands for High Temperature and LT
stands for Low Temperature.

Answer / einstein

In case of xmer-
Hv-high voltage and lv-low voltage.
In case of transmission lines-
Ht-high tension and lt-low tension.

Answer / jitender thakur

Ht is the high voltage and Lt is low voltge b/w tow binding transformer Lt is upper side and ht is lower side that is known as ht and Lt.

Answer / divya

LT Transformer transforms the voltage 66/0.44 KV

Answer / eeman

HT stands for High temperature and LT stands for low
temperature. How come HT and LT means High voltage and low
voltage respectively.

how many power plants in andhra pradesh,how many types and there capacity

2 Answers  

what is frequency transformer?

2 Answers  

Give 3 phase transformer connections for 24 pulse rectifier using thyristors.

0 Answers  

What will be the current after disconecting the bus bar or cable before discharging ?

2 Answers   Sodexo,

what is the difference between contactors & relay.

2 Answers  

What is thyristor?

13 Answers  

If one lamp connects between two phases it will glow or not?

0 Answers  

1. A 380 / 220 V r.m.s. 3-phase 4-wire circuit carries loads of 8 + j8.1 ohm; 4 + j4.1 ohm; and 2 +j2.1 ohmin the three phases respectively. The length of the circuit is 100 m, and the resistivity of the phase conductors is 0.0005 Ω/m. The neutral conductor is of the same size as the phase conductors. a) Select a reference angle 0for the first phase. Then write down the three phase voltages in both polar format and complex number format. b) Make appropriate assumptions, and take temperature effects on resistance is insignificant. Calculate the currents in the three phases. (Note: Determine conductor resistance, and apply Kirchhoff’s Voltage Law) Based on the result, suggest a main switch rating for the circuit. c) Show your preferred direction of neutral current in a diagram, and then determine its value. (Note: Apply superposition principle, and Kirchhoff’s Current Law) Use its magnitude to show that in this circuit, the unbalanced load may increase the voltage drop in some of the phases. (Note: Also observe the common volt drip in neutral) State your assumptions, if there are any. d) Suddenly the neutral wire of the circuit is broken. Estimate the new currents in the first phase, i.e. Phase L1. State your assumptions, if there are any.

0 Answers  

Is MEN and RCD related to each other ?? IF yes then how??

0 Answers  

why transmission voltages are in multiple of 11kv?

10 Answers  

WHY IN THREE PHASE CABLE 440V CURRENT FLOWS IF IN ONE PHASE 230V CURRENT FLOWS ???

3 Answers  

I use 20 nos led tube 4feet, in pathway 100mtr approximate, so what size cable i use for lighting

0 Answers   Oman Cables Industry SAOG,