What is the difference between a Junction Box and a
Marshalling Box?
Answers were Sorted based on User's Feedback
Hi Cindy,
Junction boxes are used in domestic wirings especially when
supply is to be taken through a switch to a lamp holder or
from one room to another.
Marshalling boxes better called Marshalling Kiosks(MKs) are
used in substation switchyards and in power transformers.
For switchyard MKs they contain terminal blocks to which
control cables are connected. They may also contain mcbs
and other devices. The same is true for transformer MKs.
| Is This Answer Correct ? | 93 Yes | 28 No |
Answer / engr. m, hossain
From the application point of view there is no difference
between junction box and marshaling box. Both are used for
termination and connection of cables between different
points. Usually, in the low voltage ubstation it is called
junction box and high voltage substation it is called
marshalling box.
| Is This Answer Correct ? | 43 Yes | 28 No |
Answer / manas datta
By name and application, Junction box is used simply for
junction of cables / wires. Marsheling box is also used for
the same but it may include electronic devices, switheches,
cards, fuses etc.
| Is This Answer Correct ? | 20 Yes | 11 No |
Answer / marzi nasrizade
Actually both of them are the same in action, they are used for termination and the difference is the load duty.
Marshaling box is used for heavy duty.
| Is This Answer Correct ? | 11 Yes | 12 No |
Answer / priyanka chakraborty
Junction box is mainly used for household wirings such as low voltage application.
Marshaling box is used for high voltage application. In substation or switchyard power, control and instrument cables are connected to marshalling box.
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / manish panchal
JUNCTION BOX IS USED FOR TAPPING FOR CT AND PT SUPPLY IN
SWITCHYARD. IT ALSO USED IN CONTROL TERMINALS, IT ALSO USED
AS A JOINT.
MARSHALLING BOX IS USED IN OUTDOOR APPLICATION LIKE T/R
M.BOX USED WITH WTI AND OTI IT IS ALSO USED BIG M.BOX FOR
CT/ AND PT CONNECTION.
| Is This Answer Correct ? | 4 Yes | 19 No |
Answer / k.prakashchandra
Another difference is that marshaling box is at the
beginning and junction box is in the middle, just like
between supplier and distributor.
| Is This Answer Correct ? | 8 Yes | 28 No |
Answer / vijay shinde
junction box is used in house hold.but marshalling box is
used in transformer where WTI,OTI &FAN CONTROL ARE PLACED
| Is This Answer Correct ? | 21 Yes | 46 No |
What is the function of NGR for the parallel operation of alternator? whats happen when different rating of alternator are running with parallel?
how can we connect the capacitor bank to improve the power factor?
How the flights will be fly be fly without ground connection under raining with thunder lighting?
How is earthing done in Aerospace applications such as Flights and spaceships..?
Explain Need of a starter in a dc motor.? Also explain any two starting and speed control method of dc motor?
I am going to appear for the RRB Chennai Section Engineer online exam. Please send me the question papers from 2001 to date to my mail id:upendrakrishna20@gmail.com,plz send me ,or send any other rrb papers plzzzzzzzzzzzzzzzzzz
What is the basic principal, by which DC voltage level is increased more than the supplied AC voltage during conversion. As upto AC level it is contorrled by firing anlge but after maximum level how is it possible.Please clear picture. OR we have to supply the higher level AC?
if our load in 3 phase circuit is 4000 amp. calculate the capacity of capacitor panel if line power factor is.80 .
what is the formula for calculate the turns in Transformers
When we use air circuit breaker, it has O/L protection ,time delay SC protection, Instataneous SC protection & ground fault protection. They all have some setting range. But what is the suitable/allowable setting for the above protection which will be safe for the equipment? For example-O/L protection setting have a range of (0.4,0.45,0.5,0.55,0.6,0.65,0.7,0.8,0.9,1.0)xIn Time delay SC protection have a range of (1.25,1.5,2,3,4,6,8,10,12)xIn Time delay setting is 0.02,0.1,0.2,0.3,0.4 Instataneous setting is fixed to 20xIn Gound fault setting is given 100A,300A,600A,900A,1200A This setting are for 2500A ACB. So what will be the basic allowable setting for the above protection? is there any formulae to calculate this<
Why we transmit the power at the voltage in the multiple of 11 or 1.1 like 11kv, 22kv, 66kv, 132kv...... some one told me that it is due to fomr factor 1.1 of sine wave. its fine but while transforming we can choose any voltage, so why only multiple of 1.1 there also.......? plz tell me.
Please sent me some previous year question papers of BSNL-JTO telecom and RRB in ELectrical Engineering to varshashahi@yahoo.com
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)