Answer / avdhesh

HT motors operates on high voltage ( 6.6 or 11KV). IF we
make delta connections than voltage experianced by windings
will be line voltage, which will require more insulation of
winding. In star connection voltage experinced by each
winding is phase voltage hence less insulation is required.
This is the reason HT motors always wound in star
connection.

Answer / madhanc

Normally Motors starting current when using of DOL/Delta to avoid the starting current and insulation we are using Star delta connection to protect the motor from the insulation fails and reduce starting current

Answer / shivaji chaudhari

for limiting starting current.

Answer / anand

Ht motor star connection current is root 3 times low carried & power saving but delta connection current is high

Answer / svrao

HT motors operates on high voltage ( 6.6 or 11KV). IF we
make delta connections than voltage experianced by windings
will be line voltage, which will require more insulation of
winding. In star connection voltage experinced by each
winding is phase voltage hence less insulation is required.
This is the reason HT motors always wound in star
connection.

Answer / narayanaswamy

I am of the opinion that star connection of HT motor is done to have better operation of protective gear

Answer / kumar

because ht motor starting current always high so that
motor connection should be star to delta for limiting the
starting current.the principle is that staring position
motor connection in star later it change to delta

Answer / pankaj gajare

Because HT motor having large starting current so that if
your connection will be in star then your current will be
root three so its automatically reduce.
its star delta principle...in star connection current will
root three times reduce.

Answer / jameel

the ht motor connection in star because it is easy and
cheaper than delta connection in high voltage and star
delta connection not used in this system .
and the best question here why the ht capacitor of power
factor connection star not delta although the delta
connection is more economecal than star. we need in star
three times farad(reactive power) of ccapacitor than delta
but we connection star not delta because the same reason in
ht motor.
but the ht transformer some times it is necssary to
conection the primary or the secondary or both delta
accrding to the requirment of network.

Answer / priti

in star connected sysytms...u can provide it with a
neutral..so that in case of faults the fault current will
flow through the neural nd hence preventing shocks!!

11000volt DG set carnt kaise banvay

0 Answers   AVK,

What are the various types of BUSBAR Schemes? explain each

1 Answers   NTPC,

Initially motor starts with star connection ,after few timing changes to delta connection, why the motor should run continously in star connection,it gives high torque & low current?

3 Answers  

What are the causes of unbalanced current on 34.5kv feeder Ia=0.05,Ib= 0.25, Ic=0.15 and In=0.27 prior to tripping current are balance?

0 Answers  

does a DG set has low fault level as compared to that of a transformer.If yes then why.

0 Answers  

what happen if we supply ac to the field of a alternator?

5 Answers  

why the starting torque is high in dc series motor..

3 Answers   GM General Motors,

How we calculate the Multiplying Factor of Kwh meter for 3 phase alternator.

0 Answers   Cesco,

what is the application of dynamic Breaking resistor in inverter ? & How it works ?

2 Answers  

in dc machine airgap is there b\w stator and armature but by conduction emf is generated how & what is conduction

1 Answers  

What tests should i carry over on a newly rewinded DC Generator with voltage rating of 38 volts and current rating of 350 amps, to certify that the machine is OK?

0 Answers  

What is the role of the 50 STUB protection at a GIS 400KV substation with SIEMENS protection relays?

0 Answers   Power Plant,