Answer / saiad

flaring means to removes extra gases from system to keep
system pressure in safe condition

Answer / murthy

flaring is burning of excess gases in safe area away from
plant.these can observed in almost all
petrochemical/petroleum refineries/power plants/steeel
plants wherever hydrocarbon gases which form explosive
mixtures are used.this is done due to many reasons
(1) excess gas production than requirement of downstream
plants
(2)sudden tripping of consumers i.e downstream plants
(3) gas not meeting standards required by customer i.e
downstream plants
(4)unwanted pressure increase in pipelines conneting
customer and supplier
(5) stopppage equipment like compressors,blower.
(6)even when there is pipeline leaks,gas is routed to
flares.

Answer / pradip ramoliya

Some times in refineries interconnected plant's. So, any
plant in abnormal condition that time effected to other
system and the pressure of system is abnormal. So extra
pressure and unuseful gases are remove from system for
normal condition and gases go to flare and combustion them.
That called flaring

Answer / gauravtrivedi

it is the safe and efficient disposal of relifed gases by
burning to prvevt overprssuring the equipments in plant.

What are some common problems associated with dilute phase pneumatic conveying?

0 Answers  

---

Question 58 – In the design of a solar power system steps of calculations below are followed : (a) The power output of the inverter of the of the solar panel is 100 watts. What is the power input, Pin to the inverter when the efficiency of the inverter is 50 %? (b) If the rated power of the inverter is 300 watts, how many inverter is needed for the solar panel? (c) Charge controller of V = 12 volts is used to supply power to the inverter. What is the input current I to the inverter? (d) If the charge controller capacity is 10 A, how many charge controllers are needed? (e) If a biochemical mixer consumes 100 watts, running for 2 hours per day, what is the energy consumption in kilowatt hour per day? (f) What is the input energy needed when the efficiency of the inverter is 50 %? (g) If your area receives 2.88 hours of full sunlight per day, how much energy, in kilowatt hour can be produced per day when one solar panel can produce 20 watts of power? (h) If you know that you have to produce total energy as the answer for (f), how many solar panels are needed? (i) Each V = 12 V battery has 5 ampere hours. If the total energy needed is in answer (f), then how many batteries are needed to run the biochemical mixer if without sunlight for 3 days?

1 Answers  

---

who is the first atomic scientist in india?

5 Answers   IGCAR,

---

friends....i have been searching the model paper for HPCL officer trainee for chemical eng....tat apptitude section...if u people got any information regarding tat...please send me to my mail...my id is: maruthu.flower@gmail.com...pls send me wtever information u knew....thank u....

0 Answers   HPCL,

---

Why in a continuous plant for a Hot standby screw pump system the interlock for auto starting of the other pump ( when the running pump stopped suddenly) is given with header pressure only? why not with flow rate or current of the pump?

0 Answers   Haldia,

---

why sphericle shaped vessele used for storage of petrol?

3 Answers  

---

Question 107 - In N + 1 Rule in Quantum Chemistry, whenever a spin 1 / 2 nucleus is adjacent to N other nuclei, it is split into N + 1 distinct peaks. In 1 peak or singlet, there is only 1 magnitude. In 2 peaks or doublet, the ratio of magnitude of each peak is 1 : 1. In 3 peaks or triplet, the ratio of magnitude of each peak is 1 : 2 : 1. In 4 peaks or quartet, the ratio of magnitude of each peak is 1 : 3 : 3 : 1. In 5 peaks or quintet, the ratio of magnitude of each peak is 1 : 4 : 6 : 4 : 1. (a) By using binomial coefficients or Triangle of Pascal find the ratio of magnitude of each peak if 6 peaks exists. (b) How many adjacent nuclei are available in a spin 1 / 2 nucleus in such situation of 6 peaks?

1 Answers  

---

Please describe tar, asphalt and bitumine

0 Answers  

---

why traction voltage is 25kv

0 Answers  

---

ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.28 : In the development of a small engineering facility for biochemical processing, completed contract method is applied in its construction accounting. In a short contract period, let the (contract price) = A. Let the (costs to date) = B; (estimated cost to complete) = C. (a) Find the values of : (i) estimated total costs; (ii) total estimated profit; (iii) percent completion to date. (b) If the project contract is 100 % completed : (i) find the total gross profit recognized; (ii) what is the exact numerical value of C?

1 Answers  

---

What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha?

0 Answers  

---

POLYMER ENGINEERING - QUESTION 24.2 : Let C% be the fractional crystallinity, Rs = density of sample, Ra = density of amorphous form and Rc = density of crystalline form. In a polymer, these unknowns could be related by the equation C% = (Rc / Rs) (Rs - Ra) / (Rc - Ra). (a) Find the equation of Rc as a function of C%, Rs and Ra. (b) Two samples of a polymer, C and D exist. For sample C, C% = 0.513 when Rs = 2.215 unit. For sample D, C% = 0.742 when Rs = 2.144 unit. Both samples C and D have the same values of Ra and Rc. Find the values of Ra and Rc in 6 decimal places.

1 Answers  

---