what is dc transformer? how it work?
Answers were Sorted based on User's Feedback
Answer / nikhil patil
dc transformer is nothing but of dc chopper.chopper works
as dc transformer.it can be used for step up &step down of
dc voltage.
Is This Answer Correct ? | 69 Yes | 13 No |
Answer / smartboy123
IT IS IMPOSSIBLE TO CONSTRUCT DC TRANSFORMER.
TRASFORMER IS WORKING ON MUTUAL INDUCTION PHENOMINA
Is This Answer Correct ? | 46 Yes | 29 No |
Answer / sanjeev kumar
transformer works on the principle of mutual induction and
it is immpossible to produce varing flux by dc. hence dc
transformer does not exist.
Is This Answer Correct ? | 27 Yes | 13 No |
Answer / krishna
Bull-Shit!! What DC Transformer????
There is no such thing in the world....
Transformer is a thing which works on a principle of Mutual
Induction which requires Frequency.
In DC power there is no frequency at all,
so, where is the matter of DC Transformer?
Is This Answer Correct ? | 31 Yes | 20 No |
Answer / gunnam santosh
if connect dc supply to a transformer temperature will be
increased and it gets damaged
Is This Answer Correct ? | 15 Yes | 6 No |
T/f works based on mutual induction.so if we r
give dc to that it will burn (after saturation) due
to no oposition(eb=0). Although it act like normal t/
f at starting instant. So bye using t/f we can
change ac voltage w.r.t currunt. To change dc
voltage we can use choppers.
Is This Answer Correct ? | 6 Yes | 0 No |
Answer / denzel101
You must be refering to a dc converter whereby a dc voltage
is stepped from one level to another.
I believe the poster is thinking of transformer in an ac
circuit and compare it to the device that does the same in
the dc circuits. I must say I haven't heared of a dc
transformer though.It must be wrong terminology.
Is This Answer Correct ? | 8 Yes | 3 No |
Answer / michael
Dc transformer is possible to construct but you need
additional circuit for it to work. you need a high speed
switching component for the dc to form into a AC look alike
voltage. then since the dc voltage becomes like an ac it can
create a induced voltage on the secondary winding of a dc
transformer.
Is This Answer Correct ? | 17 Yes | 14 No |
Answer / ant
transformer is a static device that works with the principle of induction. since induction an ac phenomenen,transformer can not be dc.
Is This Answer Correct ? | 3 Yes | 0 No |
we are having 15kw and 3kw motor both can run in same time , instead of using copper we are using ug aluminium cable , 35 sq.mm is suitable for its current carrying capacity..?
0 Answers Afflatus Grauver Pvt Ltd,
What is Rough Balance Busbar Protection
Why scr and igbt used in ups systeam ????
what's float charger and boost charger? why it's used?
2 Answers APCPDCL, PTCL, Rolls Royce, Siemens,
Is there any rule to select the voltage of motor based on KW rating? What is the rating above which lt motor becomes the HT motor?.
how many types control panel of a 132/33 kv substation
details of oil cell size of Breakdown voltage test of tranformer oil details as per Standardswith mushroom electrodes?
110 KW MOTER DOL STATER 240SQ.MM CABLE MOTER AND STARTER DISTANCE IS 110 METER WHAT IS VOTAGE IN MOTER END AND SYSTEM VOTAGE IS 415 V HOW I CAN CALCULTE
How much kv gas generator is needed to run 2 hp and 1 hp airconditioners, plus a refrigerator and 4 Tvs
with the help of drive can we run the 50hz motor on 100hz,what will be its effect.
bit confused - am i correct in thinking that to determine line to line voltage in a star config 110v 3 phase 4 wire distribution system i would use a voltmeter? I have a circuit configured as an unbalanced load, consisting of three incandescent lamps (1x40w, 1x60w, 1x100w - all 110v rated)connected in a star configuration to a 110v 3 phase 4 wire distribution system. I want to find out what types of meters i would use to obtain: a) each line to line voltage b) the line to neutral voltage across each load c) current flowing in each line and load d) current flowing in the neutral conductor e) power supplied to the loads im assuming i would be using ammeters in series along each line and voltmeters in parallel across each line to neutral? Also how could i predict these meter readings before taking them and with which formulae? Any help would be greatly appreciated A.
Hi, what is the temp of bus bar.