Answer / vivesh kumar

End cell voltage means the lowest voltage of cell after
that voltage if we discharge the cell then the cell losses
its normal charging characterstic and cell get damaged.

Float voltage is that voltage on which a faulty cell/deeply
discharged cell get charged .

Answer / subramanyam

Folat voltage is that; the out put voltage of the charger
just above the battery set voltage which is sufficient
enough to charge the set of batteries, without allowing the
battery set voltage to drain its attained value.

Answer / ravindra kr gupta

Float voltage means normal charging voltage when cell
charge@ C-10 ratio and when cell is discharged and nominal
chrging required.

End cell voltage means the lowest voltage of cell after
that voltage the cell losses and cell get damaged.

Answer / manu shankar

End cell voltage is the level to which the battery string voltage or cell
voltage is allowed to fall to before affecting the load.
Float voltage is the voltage at which a battery is maintained after being fully charged(boost charged) to maintain the battery capacity and compensate for the self-discharge of the battery.

Answer / ds01151

In Battery Charger we got ouly two things
1.Float Voltage
2.Boost Voltage
We got the End cell voltage when we check the single cell
voltge this should not go down less than 1.75V

Answer / shaji xavier

Float Voltage - Battery voltage at zero current (with
battery disconnected). You must wait about 20 minutes for
the battery to stabilize at this voltage.

Answer / srtlevy

Float voltage is that voltage across the battery when the
battery is conected in parallel to a float rectifier

Answer / krishna chaitanya

battery means group of cells it is connected in series
because voltage also increased you see the last cell
voltage that is float voltage

Answer / varun

float voltage is the voltage that can float in water

Just a silly question but just to make my curious mind bac to normal - Why was not 67 and 67N relays built into a single relay as i have noticed that the R,Y,B CT wiring end up into the 67 relay while the common of the R,Y,B CT wiring end up into the 67N relay. Then it was better if a single relay was manufactured just like the distance relay (21). Another question i would like to ask is - how do we know where the 67 and 67 N relay has to be placed.why is it not placed at the transformer bay? In the substaion that i am working -i have noticed that it is placed between a breaker and a common double bus bar and this line bay is connected to another substation at a remote place which is furthur connected to a load. B U S______CT for 67 & 67N ______Breaker _____ remot s/s. B A R

1 Answers  

A 3 phase motor, 440 voltage, induction motor. If we take out rotor from motor and if we give supply 440 volt to stator then what happens?????

20 Answers  

a transformer can have zero voltage regulation a)o pf b)1 pf c)lagg pf d)lead pf

2 Answers   SJVN,

In an ideal transformer no load primary current I0 A lags behind V1 by 90 degree B is in the phase with V1 C leads V1 by 90 degree D lags V1 by 45 degree

1 Answers  

if i am in front of transmission line how to know that current direction without any equipment

0 Answers  

where is the need for short circuit test for 3 see is required and why? can you explain in brief with application

0 Answers  

A car's starter motor draws a current of 100 A at 12,0 V when starting the engine. The mechanical power required to turn the engine is 960 W. At what rate is energy from the battery converted to non-mechanical forms of energy?

0 Answers   Siemens,

What is an Automatic Voltage Regultor & what is its use? What are the general componets we use to design an Automatic Voltage Regulator..What are the factors to be considered for its design?

3 Answers  

why there is a 2 slits in three pin's earthing pin?

1 Answers  

The iron loss in a 100kva transformer is 1 kw and full load copper losses are 2 kw, then what is maximum efficiency occure at a load?

3 Answers   MPSC,

What is the relay function?

2 Answers  

what is the type of winding connection( star or delta) in 1HP to 5HP motors. How to check the motor winding connections( star or delta) if not provided in the nameplate?

5 Answers