Answer / pak-engineer

hi hope all of you fine,
Friend,
as you know there are two type of earthing but tachnic are different, or you can say it Technic or various types of earthing.
1-System earthing
i-IT
ii-TNS
iii-TNC
iv-TNCS,,,,,etc
2- Equipment Earthing,
i-Bounding.\
you can get more detail if you required let me know, i will send you by mail attachment

Answer / ginijayaram

1.pipe earthing (total length 3 meter)
2.plate earthing (total 4 meter-pipe length 3 meter
1meterplate)
3.strip earthing(to take the earth value)

Answer / padm

there are two types of earthing
1) permanent earthing
2) temporary earthing

Answer / bhupendra rawat

Earthing :- Earthing means to connect the metallic part of the electric appliance or instrument threw a wire having negligible resistance to the huge mass of earth.
There are three types of earthing:-
1:- Pipe earthing:- in this earthing we use a 3-4 inches pipe of negligible resistance.
2:- Plate earthing:- in this earthing we use a Cu. or Al. plate having negligible resistance.
3:- Rod earthing:- this is also called temporary earthing. in this earthing we use a rod of negligible resistance.

and the another end which is underground is surrounded by charcoal or salt.

Answer / sophy alex

-pipe earthing
-plate earthing
-mat earthing

Answer / kirti singh

mainly 2 types of earthing
1)plate earthing
2)pipe earthing.

Answer / a rami reddy

Types of Earthing

There are various ways of doing EARTHING:

Conventional EARTHING
* Pipe Earthing,
* GI Plat Earthing,
* Cast Iron plat Earthing,
* Copper plat Earthing
Maintenance Free EARTHING

Conventional Earthing:

The Conventional system of Earthing calls for digging of a
large pit into which a GI pipe or a copper plate is
positioned amidst layers of charcoal and salt. It is
cumbersome to install only one or two pits in a day.

The Conventional system of GI pipe Earthing or copper plate
Earthing requires maintenance and pouring of water at
regular interval.

Maintenance free earthing:

It is a new type of earthing system which is ready made,
standardized, scientifically developed.

Advantages of Free earthing:

Maintenance Free: No need to pour water at regular
interval- except in sandy soil.
Consistency: Maintain stable and consistent earth
resistance around the year.
More Surface Area: The conductive compound creates a
conductive zone, which provides the increased surface area
for peak current dissipation. And also get stable reference
point.
Low earth resistance. Highly conductive. Carries high
peak current repeatedly.
No corrosion. Eco Friendly.
Long Life.
Easy Installation.

Answer / vishwas sharma

mostly we use only 3 types of earthing now a days for safty
reasons
1,pole earthing
2,plate or strip earthing
3,chemical earthing

Answer / faisal aakash

in the first answer types of earth according to construction are given
according to operational safety point of view are these
1.fixed earth
these are the earths installed by the manufacturer or during erection and use to earth that equipment these are further classified as
I.earth isolator: motor driven earth switches
II.earth switch : hand driven earth switches
2.primary earth
these are the portable earths which are used to earth the equipment under maintenance other then fixed earth.(as safety precautions) or if there is no fixed earth available beyond safety distance
3.Drain earth
when ever we are working in induction zone then this type of earth is used to ground the induction leakages.

Answer / tiger

SOLID EARTHING FOR 0-33KV
RESISTANCE EARTHING FOR >33 KV

What should be the percentage increase in length of the dead end clamp for bus bar conductor (Hawthorn) after hydraulic pressing and what should be the applied pressure?

0 Answers  

tell me working of air circuit braker.

2 Answers  

what is the basic construction diffrance between servo motor ans sqiralcage induction motor

0 Answers  

what are the factors to be considered while design the breaker either HT or LT??

0 Answers  

In case of power/distribution transformer what is percent impedence?

1 Answers  

why zero sequence impedance measurement is not applicable for single phase GT

0 Answers  

Will any motor burn if voltage provided is lesser than the rated voltage???? If yes, then how is speed control possible with voltage control

0 Answers  

How much allowable difference current between on three phases Dear sir, We have a 1870 KW HT motor, 11 Kv supply,FLA-120A,2870 rpm,2-pole squirrel cage induction Motor.And stator is connected in star connection with Liquid resistance stater to limit the starting current.It has coupled with Centrifugal air compressor.My question is it is loading 73% of FLA taking R-phase 86.7 A, Y-phase-85.4A,B-phase- 78.3A.why the B phase current is that much of difference.Is it allowable, or any one tell me how much allowable current.If any method to calculate.

1 Answers  

234 MVA Generator 3 phase Short circuit current Values required? Gen set Rating-234 MVA, Gen Voltage-18kv, PF;0.8, Xdv:23.5 %, Transformer Rating-18/380KV, 680MVA,Yndd1 two winding, Step up TR, ZT:35.50 %,X/R 4.33 Gen CB Position, CB open ,Disconnected open, Generator Running Voltage 18 Kv, Bi mistakes generator side earth switch Closed during that time short circuit current level in 3 Phase required, and how to test on site 234MVA Generator Short circuit current,

0 Answers   Jomel,

ohms law is applicable for dc or ac current or for both??? explain it berifly??

3 Answers  

In 400KV Switchyard, we have used Circuit Breaker With PIR, what is the significance of PIR & why they'r used?

2 Answers  

what is the purpose of measuring % impedence?

1 Answers