Where is the maximum temperature in refrigeration cycle?
a.Between evaporator & compressor.
b.At Compressor
c.Between compressor and condensor.
d.At condensor
Answers were Sorted based on User's Feedback
Answer / hari prasad
the answer is c
bcos work of the compressor is to compress the air so the
temperature of the air automatically increases.
so the refrigerant coming out of compressor will be high
temperature and high pressure vapour refrigerant
Is This Answer Correct ? | 24 Yes | 5 No |
Answer / kailas
Max. temperature is found at the compressor discharge port
b'cause compressor compress the refregerant and its volume
lowers & gragually rises the temperature
Is This Answer Correct ? | 13 Yes | 3 No |
c.Between compressor and condensor.
At the compressor,pressure as well as temprature of
refrigerant increases to a maximum value in the
refrigeration cycle & at the codensor temp. decreases,but
pressure does not.
Is This Answer Correct ? | 1 Yes | 0 No |
Answer / sreejith
it cant be between comp and cond coz the cond and comp temp
both are diffrt , and offcourse the comp temp is more
compared to the cond so after the comp , temp increases
and hence the closer answer is b)
Is This Answer Correct ? | 2 Yes | 2 No |
Answer / balasubramaniam
ans id B) it can't be compressor and condenser are diff temp
is high.
Is This Answer Correct ? | 2 Yes | 2 No |
Answer / pawan singh yadav
b)at condenssor
because the discharge pressure is maximum at compressor
outlet.
Is This Answer Correct ? | 1 Yes | 1 No |
Answer / vishram kulkarni
d. definitely at condenser.becoze the total heat of the
system has to be exhausted therefrom and condenser is only
a part wherefrom the system heat is given to atmosphere.
Is This Answer Correct ? | 0 Yes | 1 No |
In a four-stroke diesel engine, In what engine exhaust valve will open?
I am requiering interview questions regarding Close Ferro Crome Furnaces
1.how do you purchase the sheetmetal,machined components for OEMS? 2.WHAT IS THE SYSTEM TO BE MAINTAINE FOR PURCHASE ACTIVITY? 3.HOW DO U DO THE PRICE NEGOTIATIONS & ITS PROCEDURES? 4.WHAT ARE THE PROBLEMS WILL FACE WHILE PURCHASING THE COMPONENTS& WHAT IS THE SOLUTION TO OVERCOME BY THAT ONE 5.WHAT IS THE NECESSARY NOTES TO MAINTAIN THE PO& RELEASING THE PO?
Discuss the role of manganese in alloying steels?
25 questions in 25 minutes were asked by L&T corein mechanical engg test on 28 nov 2011 are as follows:- L&t mechanical consists of 1> airfuel ratio 2> mollier chart for flow rate 3>homogeneous or hetreogeneous mixture 4>sublimation curve 5>effect on room temperature when fridge is opened 6>cop of refrigerator 7> punching and piercing uses shear or not 8>method not used for tapering 9>forming method not used for productn 10>numerical regardng no.of cuts 11>flow of chip is controlled by which parameters 12> property important for impact loading 13>stifness of spring when it is cut into 2 pieces 14> device reqd for energy fluctuation 15> property on which rivet is selected 16>crowning to prevent flat belt pulley errors like undercut 17>cavitation occurs at which stage 18>qstn regardng inventory control 19>for ship vessel industry what sort of plantlayout reqd 20>value engg definition 21> qstn on how the extnsn occurs for uniform loading 22> qstn regardng stress actng on the shaft23>maximum value of mohr's circle diameter 24>qstn regardng meshing of teeth 25>qstn on helical gear reqrd better read G.K.PUBLISHERS GATE PAPERS ESPECIALLY FROM 1993 to 2003 ESPECIALLY THEORY QUESTIONS RATHER THAN NUMERICAL QUESTIONS
tell me about special purpose machines
even though LPG is economical than petrol,why we are not promoting LPG usage?
Where does Parallel flow heat exchanger use?
Define convection.
What trouble could result if the main engine is using a low grade of fuel?
Explain the principle of Suizer Fuel oil injection pump
present salary with all benefits (ctc) please give breakup it possible ?