Answer / naren

connect to pressure calibator, apply the low pressure -60
adjust the span into low pressure and then apply the high
pressure then adjust the span screw into high value. it is
calibrated in the range of -60 to -20.

if it is the SMART transmitter its easy, just apply URV and
LRV value through Communicator then connect to the pressure
calibator then check URV, LRV and intermediate value

Answer / ramesh

we can apply the +ve pressure to the lp side that is 60
with zero, then +ve 20 with span with respect hp open to
atmosphere

or apply -ve pressure that is vaccum to the hp side with
respect lp open to atmosphere

Answer / welcome4ujd

make the calibration set up , to get -60 , give 60 in lp
sidethen adjust zero screw, give 20 in lp side toget -20
url , and adjust span screw.

Answer / sn

apply -60 to the transmitter n make the o/p as 3 psi, then
giv -20 as the input n adjust the o/p as 15 psi.

Answer / sandeep patel

connect transmitter in bench setup, left LP side of transmitter open to atmosphere and apply -60 mmwc to HP side and check it s o/p is 4 mA or not and if it is not, then do zero trimming. then apply -20 mmwc to HP side and check o/p is 20 mA or not otherwise fo span trimming.

Answer / suresh agravat 83204 78125

Urv-LRV÷4=Span
-60=4ma
-50=8ma
-40=12ma
-30=16ma
-20=20ma
Apply pressure accroding to above chart and monitor output

Answer / anup ramteke

It depends upon the type of transmitter u are having. If its
HART based transmitter then either u can calibrate it
through HART calibrator. firstly go to basic set-up mode and
feed the URV as well as LRV values. And if u want to
calibrate it at field itself when HART calibrator is not
available then u can set LRV value by entering its value in
mode 2 whereas for URV its mode 3.

Answer / suvendu sekhar giri

You can give positive pressure on low pr side keeping the
high side open to atomosphere for lrv (-60) & urv (-20)or
you can give negative pressure on high pr side for lrv(-60)
& urv(-20) keeping low side open to atomosphere.You can
adjust zero at lrv & span at urv. If it is smart
transmitter then you can zero trimming keeping both the low
& high pressure side open to atmosphere.

Answer / venkat

actually we can calibrate LP side by positive pressure and
Hp side also we can calibrate by negative pressure but LP
side better

how can we calibate ph meter. how can we calibrat conductivimeter how can we calibrat massflowmeter & it s working.

1 Answers  

what is interface level and how it is calibrate?

0 Answers  

How u measure the massflow in orifice flow measurement techniques

0 Answers   Johnson Matthey,

What should we do when Fisher Fieldvue DVC2000 give some out put air at 4mA bt at that i need no out put

1 Answers  

what is interface level measurement.who can calibrate interface level measurement transmitter online

0 Answers  

why we use only 4 to 20ma other than 0 to 16 ma

5 Answers   Invensys, Systech,

What is the load line in control valve?

1 Answers   IFFCO,

What is the standard height for stancion supports? and what is the standard mounting height for different transmitters?

11 Answers   Samsung,

What is the function of solenoid valve in on/off & shutdown valve and why it is not used in control valve normally?

0 Answers  

what is the protection system in solar turbine compressor

0 Answers  

what is wave length were using ?

0 Answers  

what is difference between profibus and field bus?

1 Answers