Answer / moti rgpv

CU STRIP IS MORE CONDUCTIVE THEN GI STRIP.
SO LEAKAGE CURRENT OF X-MER GET LOW RESISTIVE PATH.

YES IT AFFECT IN FOME OF HEAT

Answer / sam

no issue in using GI strip for transformer earthing, but the problem is the GI strip used should be of sufficient size while copper strip used can be of reduced size, so places where space constraints occur, copper strips are used, moreover economical considerations are also important in chosing the strips. It won't affect the transformer performance if GI is used instead of copper.

Answer / mallikarjuna reddy

Electrical peoples widely used cu strips instead of GI
strips for transformer neutral,because whenever unbalance
currents occurs in the line it have to flow to the
ground,for this we need high conductivity material.thats
why we are using cu. strip instead of GI strip.usually
copper is an high conductivity material than GI material

Answer / shivshakti

Copper Material current carring capacity is more than GI material. so when ever any fault current occurs, they can easily pass through copper material instead of GI. so we are used copper

Answer / bala

If we use GI strip instead of cu. The benefit is cost and also GI resist the fault current than cu, so the level of fault current Is slightly reduced than using cu. ...

Answer / rk

GI strip can be used insted of cu but it must be capable of
conduting the current without overheating. now GI strips
are pleantly used everywhere as per cost consideratuon.

Answer / vaseekaran

we can use GI strips only for home purpose.when we recomend
for companys and transformers cu strips are more prforable
bcoz of its conducting capacity and with standing capacity
of heat and bending quality of its propotion.

can we use HPSV LAMP in HPMV LAMP fixture ?and viseversa.

5 Answers   OPS,

explain the f=np/120 this equ.how to come 120

3 Answers   Jayaswal Neco Industries,

WHAT IS THE DIFFERENCE BETWEEN A DC MACHINE OUTPUT AND RECTIFIER OUTPUT...

3 Answers   Cesco, NTPC, RRB,

what is starting current and use of starting current?

3 Answers  

solor panels arrange some angle,panel is flat fitted energy was produced or not why?

0 Answers  

whats the reletion betweet flow,pressure,head,rpm and motor rating?

1 Answers  

in a dc motor we supply current only to the armature conductors,from where is the field winding gets excited then??

3 Answers   RRB, Siemens,

what is joule?

2 Answers  

How much CTs are required to measure th curent in DOL starting of motor?PLs explain.

1 Answers  

why dont we connect the two 12 V DC batteries in parallel, for an inverter (UPS)? is there any harm ?

6 Answers  

On load tap changer (OLTC) explode? Transformer Vector group: Ynd11 Rated Power: 353MVA Rated Current: 693A Voltage:294/20KV OLTC Type: T III Y1000 110/c 12193w Max Operation Current: 295A Step Voltage: 550V Arrangement in Tx windings: Y Connection Problem: Damage of Unit 1 Generator Transformer On Load Tap Changer (OLTC) Description of Incident: 9.00 a.m. :- Generator No Load test on excitation system started 10.30 a.m :- Carried out AVR change over test 11.30 a.m :- Preparation for Generator Manual Synchronizing test 12.00 a.m :- Manual Synshronizing test started. Observed incoming generator voltage higher than running voltage. CECR operator operated Generator Transformer OLTC to bring down the incoming generator voltage 12.03 a.m :-Generator Transformer abnormal alarm operated at Gen.Control Desk (CECR) CECR operater at Generator transformer bay informed that the transformer oil splashed out from OLTC. CECR operater informed that he heard explosion inside OLTC. Observed Oil level & Oil Flow alaram operated at Tranformer local annunciator. 12.05 am :- CECR operator 'Open Gen Field Breaker” 12.10 a.m. :- Elec1 team inspected the OLTC and found the OLTC rupture disk was broken and oil spilled at OLTC area. - Elec1 found the OLTC top cover bulging. Do anyone know why and possibility cause happen in this OLTC.

9 Answers  

What is the difference between Welding Transformer and Normal Transformer?.

2 Answers   DAE,