what is advantage in open delta connection?
Answers were Sorted based on User's Feedback
Answer / iqbal ahmad
The very useful advantage of open delta connection is to
detect ground fault at any bus or line of a system. usually
open delta connection transformer is used in potential
transformer to detect ground fault as a 3rd core of PT.
Is This Answer Correct ? | 66 Yes | 20 No |
Answer / swapnil
with use of open delta connection maintenance of
transformers is possible . If load on two transformers
increase than we can install another transformer and close
the delta in future .
Is This Answer Correct ? | 45 Yes | 12 No |
Answer / sam khanji
open Delta will supply 57% if its rated value and give the
apportunity to increase the ratio by adding the missing leg
to become a complete delta.
Is This Answer Correct ? | 38 Yes | 16 No |
Answer / niranajn
An open delta connection can supply power at 53.3% of its
rated value.
Is This Answer Correct ? | 46 Yes | 27 No |
Answer / derekdejs64
In three phase system it use for Directional Earth Fault
relay voltage element.
Is This Answer Correct ? | 38 Yes | 21 No |
Answer / dnyaneshwar
in unearth sysytem open delta connection is used for
detecting of earth fault & single phasing of equipment.
plz, anybody give another ans......
then welcome.
Is This Answer Correct ? | 40 Yes | 30 No |
Answer / imtiaz khan
There are two biggest advantages:
1) In an unearthed system like capacitor banks, it is possible to detect ground faults though earth path is not available.
2) In case of bulk power transmission where transformer banks are used, their advantage is that if one leg is out for maintenance/replacement than also approx. 57% power can be transmitted.
Is This Answer Correct ? | 14 Yes | 4 No |
Answer / subhankar nath
By the open delta connection of PT we can monitor the
neutral shifting of the system as well as it can be use in
the genetating end substation for the maintenance of the
transformer in the time of low load demand.
Is This Answer Correct ? | 18 Yes | 11 No |
Answer / hitesh gohil
An open delta connected when full power is not needed.
Is This Answer Correct ? | 16 Yes | 13 No |
Answer / ram
Open Delta Connection Means Potenial Transformer Secondary
Series Connection Was Given,And Grounded.This Line Was Zero
Potenial,When Voltage Flow For This Line Open And Trip The
Relay.Unbalace Voltage Came Also Trip The Ckt.
Is This Answer Correct ? | 3 Yes | 0 No |
how to calculate the neautral earthing conductor size for a 500kva dg set.
Which are resistive loads & which one are inductive loads : Refrigerator, Split air conditioner, ceiling fans, well pump, fluoresecent bulbs, T.V, CRT Monitors, Adsl Routers, C.P.U, Printers, Deep Freezers, Speakers, DVD Players, Microwave oven etc. ? Output Power for these Appliances Would be same like this : P = V * A * P.F Or would be changed ? thanks
importance of air gap in transformer
what is difference b/w earth and ground?
why transformer rating in KVA ?
8 Answers Bhel, TATA, Voltage,
why some transmission lines have 7 wires n why some have 3 n 4??
IN PLATE EARTHING , PLATE LAID IN VERTICAL POSITION ,WHY HORIZONTAL WHY NOT
On what principle electric motor works?
WHAT IS DC COMPONENT IN CIRCUIT BREAKER?
Why Ferranti effect is occoured in leading power factor load in a overhead transmission line?
Give idea about General Engineering. From which book i can study this topic. Pl. reply me via email. My email is ravi@bhelhwr.co.in, also give the name of book/website, from where i can prepare it.
10. THE MOST COMMON TYPE OF THREE PHASE IN UNSYMMETRICAL FAULTS IS ........