Answer / john

HT is High Tension Cable whereas LT is Low Tension Cable

Answer / bk

Basic difference is the dielectric strength/ thickness of
insulation. For LV PVC is OK. However, for HT cable cross
linked poly ethylene(XLPE) is used.

Answer / sanketh

In High Tension cable there is no Neutral.In market will
get only 1,3 core cbles where as in LT cable there is a
neutral U have to prefer for 3.5 or 4 core cable.HT cable
having Screen to avoid voids and cavities.

Answer / rammy

The basic differance betwwen the HT and LT cable is
insulation of the cable. Because of insulation is always
govern by voltage level so we have higher on HT cable
compare to LT cable

Answer / rk sharma

LT HT
1. Use Below 450V Above 500
2. Insulation PVC XLPE
3. Core(Neutral) Yes No
4. Grading 1100 V Above 11KV
5. O.D. - Lesser than LT
6. Current
Carring Cap. - Greater than LT

Answer / suneet chauhan

the basic diff is of grading of the cable.
for HT- 6.35/11 Kv
for LT-1100 Voit

Answer / hari das

HT is High Tension Cable whereas LT is Low Tension Cable

Answer / er. ankush miglani 9718151073

lt cable contains neutral
wareas dere is no neutral in ht cables

Answer / vinay kr. gupta

basic difference between HT and LT cable is in HT cable
insulation three layer two of semi con compound and one
layer of XLPE compound but in LT cable insulation only in
one layer of XLPE for bear the High voltage .

Answer / rk sharma

Difference between LT and HT
1. Use Below 450V Above 500
2. Insulation PVC XLPE
3. Core(Neutral) Yes No
4. Grading 1100 V Above 11KV
5. O.D. - Lesser than LT
6. Current
Carring Cap. - Greater than LT

how can you calculate the value of external resistance inserted in a slipring industion motor? (eg. 110 kw / 990 rpm/50Hz/stator v-415/stator Amp-195/Rotor V-440/Rotor amps- 151.)

6 Answers   Bosch, NMDC,

TELL ME WHAT IS INDUCTOR AND CAPACITOR WHAT IS IT BASIC OPERATION ANDFUNCTION?

0 Answers   ABC,

Why transformer use to generator neutral earthing purpose ?

1 Answers  

I have 11KV/415V power distribution transformer. I have found unbalance current in LT (415V) side. Also observed that unbalance voltage (3V) at LV side due to HV side unbalance voltage. What should I check for this? Also, the same LV side load can run in balance on captive power.

1 Answers  

what are d/f between cfl and pl lamps,

1 Answers  

how to calculate the current capacity of a wire if its dimension in Square mm is given

1 Answers   TATA,

for preparation of design note of 11 / 220 kV , 3 phase, 63 MVA transformer how can calculate or consider the iron losses and copper losses

1 Answers  

I have applied the post Junior Engineer-iii(c&w)in R.R.B chennaI recently . can i get any model question paper LAST 4 YEARS?

2 Answers   Data Entry Operator, RRB, SSC,

what happen when dc shunt motor field is sudden open in running condition

34 Answers   APGenco, Bhel, IIT, JMRC, TCS,

in ct secondary one terminal is connected to earth why?

1 Answers  

please give some hindalco placement papers for written exam

0 Answers   Hindalco,

In a star to star transformer can we use a common neutral for both star connected primary and secondary

1 Answers