Answer / bkmutha

If insulation grade is 1.1 kv then we called it LT cable
and above it i.e. 3.3 kv , 11 kv we called as HT cable.
in short we can say that main difference is insulation or
property of insulation to withstand voltage stress.

Answer / jacobdaniel

HT Cable:- 1) Its design having 4 to 5 layer of protection
to withstand the high tension voltage and also we can avoid
Voltage drop because of sensitive protection.
2)Bundle Conductor of HT Cable thickness is high than LT cable
3)HT Cable having R,Y & B Terminals without Neutral

LT Cable:- 1)Its design having 2 to 3 layer of Protection to
withstand the Low Tension Voltage.
2)LT Cable having R,Y & B Terminals with Neutral

Answer / ankit jain

In general we only use two words ie. LT & HT cable.
LT = below 500V
HT=Above 500V

But as per IS standard:
there are following voltage grades.

below 1000 V = LV
1100 V < MV < 36 KV
66 KV < HV < 150 KV
150 KV < EHV < 525 KV

We generally use PVC insulation for LV And MV cables. But it
is not compulsary to use PVC Cables as now XLPE cables are
more preffered because of certain advantages over PVC
Insulation.

Answer / maneesh kumar

HT cable made in high voltage and LT cable made in high
current.

Answer / selvakrishna.s

HT Cable:- 1) Its design having 4 to 5 layer of protection
to withstand the high tension voltage and also we can avoid
Voltage drop because of sensitive protection.
2)Bundle Conductor of HT Cable thickness is high than LT cable
3)HT Cable having R,Y & B Terminals without Neutral

LT Cable:- 1)Its design having 2 to 3 layer of Protection to
withstand the Low Tension Voltage.
2)LT Cable having R,Y & B Terminals with Neutral

Answer / kaushik sarkar

In HT cable the insulation grade is much more higher then LT
cable.
Lt cable can maximum withstand 1.1kv but whereas Ht cable
can withstand much more.
Lt cable can come with 'N',but there is no 'N' in Ht.

Answer / a k sigh

HT cable is used for 1KV to 11KV voltage rating whereas LT cable is used upto 1KV. The basic difference in their insulation level/thichness, it is higher in HT cable LT cable.

Answer / kunal singh dabi

For LT cable

1. Use : Up to 690V

2. Insulation : PVC
3. Core(Neutral) : Yes
4. Insulation Grading : 1100 V

For HT cable

1. Use : Above 690
2. Insulation : XLPE
3. Core(Neutral) : No
4. Insulation Grading : Above 3.3kV, 11KV..etc

( Please note that now 690 V using in VFD application with
LV cable and 440 V for DOT motor starter)

Answer / sandeep thakur

In HT cable there is only three phase and one messanger wire,and its collects neutral from where the supply is come.

where in LT cable there is three phase,one neutral and one wire is for street light.

Answer / kishan dewangan

Both are approximate same, the only main differences
between them that is insulation.Insulation level will be
high of HT cable because it will be sustand high voltage.

what is solkor relay and which condition it will act?

0 Answers   Equate, TCS,

What will be the output voltage of a transformer if it is primarily energized from a square wave voltage source?

0 Answers   HPCL,

what is the difference between the characteristics of two different phase bushing of any transformer

0 Answers   NIT,

The efficiency of a 100kva transformer is 0.98 at full load as well as half load , for this transformer what is the Copper loss at full load ?

0 Answers  

why the colour of insultor stack , petticoat is brown. Is it has some technical reason.

0 Answers  

what is the operation of Control Module(CM),MONITOR Module(MM), MONITOR Module DUAL (MM2),Signal Module(SM),Isolator Module(IM), please some one reply me.. the operation and application of these in FIRE ALARM SYSTEMS...

1 Answers  

what are different type of triping equipmen like MCB,MCCB and their differences

3 Answers   ABB, Schneider, UPPCL,

which type of harmonics minimum produce in 12 pulse rectiformer transformer? a)3rd b)5th c)7th d)11th

4 Answers   Power Grid, Powerica,

why does not tester light up when it is touched to neutral of 3 pin socket.

4 Answers  

What is the comparision (advantages / disadvantages) of 110V, 60 Hz system to 230 V, 50 Hz system.

2 Answers  

what is the difference b/w single and three phase circuits?

1 Answers  

how the inner and outer body is separated in aircrafts?

0 Answers