which mechanism is used to turn the vehicles?
Answers were Sorted based on User's Feedback
Answer / suresh kp
Ackerman steering mechanism
|Is This Answer Correct ?||98 Yes||2 No|
Answer / sandeep..appearing at 14july08
davis steering is most accurate one but due to short life
of it by frictional sliding link; alternate Ackermann
steering mechanism is used for same...while it is
theoritically correct for three conditions only. but
practical more realible & so widely used.
differential is used to prevent the slip of inner wheel
while taking a turn on road...to get better control at turn
& higher life of tyre and al dat.
|Is This Answer Correct ?||62 Yes||1 No|
Answer / sunil singh_9419655448
the differential mechanism
|Is This Answer Correct ?||55 Yes||20 No|
Answer / abhinay
Steering Gear Mechanism
1. ackerman gear mechanism
2. davis steering gear mechanism
|Is This Answer Correct ?||25 Yes||1 No|
Answer / devesh singh thakur
Ackerman and Davis there are two mechanism used to turn the
vehicles in required direction .
|Is This Answer Correct ?||9 Yes||0 No|
Answer / arun prasath
|Is This Answer Correct ?||6 Yes||0 No|
Answer / pramod
steering gear mechanism is used to take turn and
differential mechanism is used because while taking turn one
wheel one of the wheel require to travel more distance than
the other in the same time.hence in order to obtain
different speeds for both wheel differential box is used.
|Is This Answer Correct ?||6 Yes||3 No|
Answer / asheesh aswal
ackerman and davis steering mechamism is theoretically used
to turn vehicles but the vehicle may not skid while taking
the turn during steering, differential is used in four
|Is This Answer Correct ?||3 Yes||0 No|
Answer / jeevan jyoti namdev
|Is This Answer Correct ?||3 Yes||2 No|
Answer / nizam
racker arm steering mechanism,rack and pinion,ball and race is the one type of steering mechanism,differential unit.
|Is This Answer Correct ?||0 Yes||0 No|
How with alloying of steel it is possible to a achieve properties which can not be achieved with heat treatment ?
25 questions in 25 minutes were asked by L&T corein mechanical engg test on 28 nov 2011 are as follows:- L&t mechanical consists of 1> airfuel ratio 2> mollier chart for flow rate 3>homogeneous or hetreogeneous mixture 4>sublimation curve 5>effect on room temperature when fridge is opened 6>cop of refrigerator 7> punching and piercing uses shear or not 8>method not used for tapering 9>forming method not used for productn 10>numerical regardng no.of cuts 11>flow of chip is controlled by which parameters 12> property important for impact loading 13>stifness of spring when it is cut into 2 pieces 14> device reqd for energy fluctuation 15> property on which rivet is selected 16>crowning to prevent flat belt pulley errors like undercut 17>cavitation occurs at which stage 18>qstn regardng inventory control 19>for ship vessel industry what sort of plantlayout reqd 20>value engg definition 21> qstn on how the extnsn occurs for uniform loading 22> qstn regardng stress actng on the shaft23>maximum value of mohr's circle diameter 24>qstn regardng meshing of teeth 25>qstn on helical gear reqrd better read G.K.PUBLISHERS GATE PAPERS ESPECIALLY FROM 1993 to 2003 ESPECIALLY THEORY QUESTIONS RATHER THAN NUMERICAL QUESTIONS
which mechanism is used to turn the vehicle?
Would you please provide me with questions collected for interview regard to pressure vessel, which is in the aspects of welding, NDT, materials and painting? Please send these questions&answers to email@example.com within 1 week, Thank you for your help. Rgs!
could you tel me the kind of questions general asked by technical round about ERP.
what is Investment casting? how it is differ from other casting process?
what is the function of gland in steam turbines? what is requirement of de-superheating is steam turbines what is the purpose of spray line for gland
What is the difference between stalling and surging in rotary compressions ?
What trouble could result if the main engine is using a low grade of fuel?
State the laws of thermodynamics and its importance of in mechanical engineering.
how piston moves from bdc to tdc during compression stroke. which force acted to compress the fuel at pressure....
What is long form of FIAT