Answer / dinesh kumar

TRANSFORMER OIL BDV is carried out as per IS-336 for nomal
and IS-12463 for High viscosity oil.
1.Take one sample from top of Transformer and one from the
bottom of transformer.
2.The BDV of oil should withstood min 50 KV
3.The gap between the test sample is 2.5mm maintained
4.Each sample(top/bottom) should be checked seperately
5.Procedure
a.Voltage should be gradually increased from 0.
b. At one point Flash will take place and that point is
termed as Bread down Voltage

Answer / selvan

answer 1 is very correct.

Answer / sri rama murthy

the breakdown voltage need not be 50kv but the min BDV is
30kv at 2.5mm gap between the electrodes

Answer / hamed

Regarding the withstand voltage I think It depends on the
type and quality of the oil itself.

Answer / deepak sharma

Please anyone can tell me the dia. of the electrodes?????

Answer / v.b.vijay anand

At first thing you maintain the electrical norms..To Take one sample from top of Transformer and one from the
bottom of transformer.
On before take oil samples you should confirm the moisture particles removed are not..
And then removed the air boubles in that vessel between the electrode...
The BDV of oil should withstood min 50 KV...
The gap between the test sample is 2.5mm maintained..
Voltage should be gradually increased from 0.
You will wait min 30min then only you will get good result..

Answer / muhammad owais

tell me why take sample both side (top/bottom)?
why not take from bottom any problem

Answer / saravanan.m

*Take one sample from top of Transformer and one from the
bottom of transformer.
*The BDV of oil should withstood min 50 KV
*The gap between the test sample is 2.5mm maintained
*Each sample(top/bottom) should be checked seperately
*Procedure
a.Voltage should be gradually increased from 0.
b.At one point Flash will take place and that point is
termed as Bread down Voltage.
*If its withstand means the viscosity of transformer oil is
good

Answer / suthagar.s

that means the transformer oil withstand the temparature
capacity that is called as breakdown voltage test in
transformer

what is the circulate the diesel in DG in side pls tell parts name and picture with circulate the diesel

0 Answers   Mukand,

when a three phase motor in running condition consumes 2A in each phase,and if one of the phase gets fails what will be the consumption in other two phases

4 Answers  

All the voltage drops and the source voltage added together in a series circuit is equal to

2 Answers  

there is a power transformer 66/11kV in delta-delta connection has 5 feeder coming out from the secondary side. One of the feeder in it normally loaded (loaded than other feeder)and this feeder usually trips with double OCR causing the bank transformer to trip. Now if the load of this feeder is put on other transformer then that no problems occurs on that transformer or the load. However normally all the test(IR, PI, short ckt, open ckt,grounding test and other ) has been conducted for this but evertything transformer..... I am not geting what is the actual problem...

2 Answers  

in control scheme dc logic wiring commonly using negative loop,what is the reason?if we use positive looping what will happen?

0 Answers   DNJ Energy LLC, WI,

please design a rectifier with batteries for below requirement and also explain how you calculate this solution, Load = 700Amp DC Backup time = 6 hour. please explain briefly ?????

1 Answers   GNFC,

CAN CU XLPE/PVC CABLE BE USED INPLACE OF LOW NOISE SCREENED CABLE? KINDLY GIVE REASONS

0 Answers  

why transformer tank is in rectangular shape what happen when it is in step shape

0 Answers  

how to calculate the bus bar current rating

2 Answers  

whether choke act as a voltage regulator in tubelight or not?

1 Answers   Bhel,

What is the permissible maximum flux density in transformer core?

0 Answers  

How can i calculate heat load ?

3 Answers   DSSR, NSN,