What are the loads considered when designing the Nut and Bolts?

Categories >> Engineering >> Mechanical Engineering
Suggest New Category

What are the loads considered when designing the Nut and
Bolts?

Question Posted / bhyrappa

12 Answers
17980 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What are the loads considered when designing the Nut and Bolts?..

Answer / phani

bolt must be resist to highly tensile stress and nut must
be resist to highly compression

Is This Answer Correct ?

14 Yes

0 No

What are the loads considered when designing the Nut and Bolts?..

Answer / raju

Shear Loads & crushing loads

Is This Answer Correct ?

4 Yes

3 No

What are the loads considered when designing the Nut and Bolts?..

Answer / raju

Shear Loads & crushing loads

Is This Answer Correct ?

3 Yes

3 No

What are the loads considered when designing the Nut and Bolts?..

Answer / ramshankar varun

BOLT will get high tensile stress and little shear stress
while nut resist crushing stress.

Is This Answer Correct ?

0 Yes

0 No

What are the loads considered when designing the Nut and Bolts?..

Answer / manisha boxi

shearing and crushing load

Is This Answer Correct ?

0 Yes

0 No

What are the loads considered when designing the Nut and Bolts?..

Answer / shekhar

shear loads & crushing loads

Is This Answer Correct ?

2 Yes

3 No

What are the loads considered when designing the Nut and Bolts?..

Answer / ajay

shear load and crushing load

Is This Answer Correct ?

1 Yes

3 No

What are the loads considered when designing the Nut and Bolts?..

Answer / arun giri

axial tensional load and shear load

Is This Answer Correct ?

0 Yes

2 No

What are the loads considered when designing the Nut and Bolts?..

Answer / velladurai

shear & crushing

Is This Answer Correct ?

0 Yes

2 No

What are the loads considered when designing the Nut and Bolts?..

Answer / manju

Shear Loads & axial loads

Is This Answer Correct ?

1 Yes

4 No

Post New Answer

More Mechanical Engineering Interview Questions

1.In modal analysis ,we can give damping or not? 2.draw goodman's rankine fatigue curve? 3.write down goodman's rankine fatigue equation? 4.IN structural analysis ,out of so many stresses,why von-mises stress are chosen?

1 Answers Infotech,

What is volumatric air change of a HOT GAS GENERATOR of a STEAM BOILER ?

0 Answers Lanco, Microsoft,

what is servo motar?

2 Answers Visa Steel,

Categories >> Engineering >> Mechanical Engineering Suggest New Category Question Asked @ Answers Views select what is advantage of hllow shaft over solid shaft aprt from material saving? does hollow shaft absorb more vibration than solid shaft? 0 5 wat is the meaning of cop of wet suction and dry suction????? 1 171 What is the difference between an axle and a shaft? reply soon frnds........ 4 260 16 inch = 1 ______________? 2 124 What are the steps taken in troubleshooting of a machine e.g extruder ME 0 26 What is a seal? ME 3 133 what is the mean of b.tech? 3 167 what type of pump 2 63 what is differance between ball screw and lead screw ? Amtek 1 86 What is the units of surface tension and also dimensional formula? RRB 3 218 What is meant by cigarcone? RRB 3 120 I want to know flow rate,max pressure drop,heat load,design pressure,test presurre,temp both inlet and outlet of coldside and hot side of 1,2,3,5,5.5,7.5,10,12,15 tons 0 24 why steam power plant is more popular than gas turbine plant? ME 3 304 what is EEE in thermodynamics????? ME 2 223 what is the practical use of ENTROPY? JSW 4 282

1 Answers

what is supercharging?

7 Answers BEL,

What will you check if one cylinder of your engine is not like the others?

1 Answers

what precautions must be used when water washing a boiler?

0 Answers

Why would you use hydraulics rather than pneumatics?

0 Answers

What is higher IMP or BHR

0 Answers

Please provide me Hindustan Pretroleum Question Paper with Answers