Answer / kangchuentat

Answer 92 - (a) By fraction of concentration, [ settled chromatography medium volume (L) ] / [ slurry volume (L) ] = slurry concentration (%) / 100. Then [ slurry volume (L) ] = [ settled chromatography medium volume (L) ] / [ slurry concentration (%) / 100 ]. (b) By fraction of volume, [ sample volume to be processed (L) ] / [ chromatography medium volume (L) ] = sample volume in percent total volume (%) / 100. Then chromatography medium volume (L) = [ sample volume to be processed (L) ] / [ sample volume in percent of total column volume (%) / 100 ]. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.

Why is post-weld heat treatment (stress relieving) sometimes necessary for welded vessels?

0 Answers  

---

Question 29 – For a Vernier scale that consists of 0.11 cm per section, estimate the length on actual standard ruler of 0.1 cm per section for 2.39 m and 0.91 m.

1 Answers  

---

What is the characteristic length for slab?

0 Answers  

---

ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.11 : Let an Accounting Equation to be : Assets = Liabilities + Equity of Owner. In a biochemical engineering organization, its account balance sheet contains the following information : Accounts payable $2200; accounts receivable $1500; line of credit $500; cash $100; long term debt $3800; inventory $1300; investments $800; plant equipment $6800. Find the equity of owner by applying Accounting Equation.

1 Answers  

---

ENGINEERING DRAWING - EXAMPLE 18.3 : Autocad computer program is used to draw a pipe that is used to transport natural gases for processing. Actual length of the pipe is 10 metres. The pipe has cross sectional area of circle in shape with measured circumference of s = 3 metres. (a) If 10 units are used to represent the actual length of the pipe in computerised engineering drawing, find the diameter of the pipe, d that will be shown in the engineering drawing. (b) If one unit in the program equals to 1 centimetre, find the scale used in the computer program.

1 Answers  

---

---

HOw to derive reynolds equation?

1 Answers  

---

I am pg student of chemical engg. I am intrested Heat Transfer Subject . I want information about advance heat transfer related PG PROJECT

0 Answers  

---

ELECTRICAL TECHNOLOGY - EXAMPLE 16.3 : In the design of a solar power system steps of calculations below are followed : (a) The power output of the inverter of the solar panel is 100 watts. What is the power input, Pin to the inverter when the efficiency of the inverter is 50 %? (b) If the rated power of the inverter is 300 watts, how many inverter is needed for the solar panel? (c) Charge controller of V = 12 volts is used to supply power to the inverter. What is the input current I to the inverter? (d) If the charge controller capacity is 10 A, how many charge controllers are needed? (e) If a biochemical mixer consumes 100 watts, running for 2 hours per day, what is the energy consumption in kilowatt hour per day? (f) What is the input energy needed when the efficiency of the inverter is 50 %? (g) If your area receives 2.88 hours of full sunlight per day, how much energy, in kilowatt hour can be produced per day when one solar panel can produce 20 watts of power? (h) If you know that you have to produce total energy as the answer for (f), how many solar panels are needed? (i) Each V = 12 V battery has 5 ampere hours. If the total energy needed is in answer (f), then how many batteries are needed to run the biochemical mixer if without sunlight for 3 days?

1 Answers  

---

How to calculate the release flowrates from pressurized gas systems?

1 Answers   Reliance,

---

Explain how can one estimate how the friction factor changes in heat exchanger tubes with a change in temperature?

0 Answers  

---

Explain what are some good uses of low-grade steam at 12 atm and 1920c?

0 Answers  

---

ENGINEERING MATHEMATICS - EXAMPLE 8.3 : Solve the first order differential equation : (Z + 1)(dy/dx) = xy in term of ln |y| = f(x). Z = (x)(x).

1 Answers  

---