-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.wha

Categories >> Engineering >> Instrumentation
Suggest New Category

-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.what is the range in 12mA?

Question Posted / zia

5 Answers
5939 Views
NCC, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.what is the range in 12..

Answer / piyush

150

Is This Answer Correct ?

15 Yes

1 No

-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.what is the range in 12..

Answer / am

12 mA is 50% of the signal range (4 to 20 mA).
Here, transmitter range is -200 to 500 mmWC. That means its span is 700 mmWC. So, 50 % of the range will be 350, which we have to add to the lower range. That is 350+ (-200) = 150 mmWC.

Is This Answer Correct ?

5 Yes

1 No

-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.what is the range in 12..

Answer / suresh agravat

-200 to 500(urv-lrv)/span
700span
-200=4mA
-25=8mA
150=12mA
325=16mA
500=20mA

Is This Answer Correct ?

2 Yes

0 No

-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.what is the range in 12..

Answer / muhammed shafeeq

sry
pls add formula

Is This Answer Correct ?

0 Yes

0 No

-200mmwc to 500mmwc range transmitter have there 4mA is -200 and 20mA is 500.what is the range in 12..

Answer / rampal.m.

-200 for 4ma and 500 for 20ma so span 16ma for span 700 that why
16ma for 700
1ma for 700/16 so 12ma for 700/16 and multiply by12ma=525
this -200+525=325
ans is for 12ma
=325mmwc

Is This Answer Correct ?

0 Yes

5 No

Post New Answer

More Instrumentation Interview Questions

Could anybody pls give ans of boiler 3 element control system?

5 Answers Qatar Petroleums,

LADDER LOGIC Can any body state Logic on following condition Instructions to use 1-XIC 2-XIO 3-Output ONLY Program Push 1st button On - 1st lamp should On Then Push 1st button Off - 1st Lamp Should remain on Push 2nd button On - 1st lamp should Off and 2nd lamp should On Then Push 2nd button Off - 2nd Lamp Should remain on.

4 Answers

is there any digitel grevity meter availaible in the market by which we can measure specific gravity of a battery?

0 Answers

what is o2 analyzer and how it measured ,what is the role of this analyzer in cfbc boiler...

0 Answers Mittal Steel,

can you give some devices that measure directly the mass flow rate.

1 Answers Takreer,

if my 6 kva UPS gives 20 min. backup at 100 % load, then at 25% load what is the backup time?

17 Answers

Anybody know how to create a ladder programme for power switch in TV remote without using counter... ie TV can be turn on and turn off using single push button switch... on pressing the switch first time TV turn on and hold the on state till i press the switch again, and after TV turn off.

2 Answers

can anyone tel the syllabus or previous year question paper for BHAVINI(EIE)2014.

0 Answers Bhavini,

any one suggest me how to calculate percentage of air leakage with formula,

0 Answers SSL,

How to calculate 47Liter H2 Gas cyilnder consumtion? Cylinder inlet Pressure is 200bar and Discharge pressure is 6.0bar. Flow is 100ml/min.For the above condition how many days one cylinder can be used?

1 Answers

what is meant by turn down ratio?

3 Answers Avant Garde,

why does mA signal preferred for signal transmission?

12 Answers Emerson,

For more Instrumentation Interview Questions Click Here