Calculate the cooling duty, H required to condense and cool acetone from 100 degree Celsius to 25 degree Celsius at atmospheric pressure. The heat of vaporization for acetone at its normal boiling point is 30.2 kJ / mol. The boiling point of acetone at atmospheric pressure is 56 degree Celsius. The flowrate of acetone through the condenser is 100 mol / s = N. Value of sensible heat needed to increase the temperature of acetone in liquid form from 25 to 56 degree Celsius is 4.06 kJ / mol. Value of sensible heat needed to increase the temperature of acetone in vapor form from 56 to 100 degree Celsius is 3.82 kJ / mol. Unit of H is kJ / s.
- 1 Answers
- 3733 Views
- I also Faced
- E-Mail Answers
Answer / kang chuen tat (malaysia - pen
Answer 13 : In the same state, total heat changes in heating = total heat changes in cooling for acetone. H = N ( total heat of sensible + heat of vaporization) = 100 (mol / s) [ (30.2) + (4.06 + 3.82) ] (kJ / mol) = 3808 kJ / s. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.
| Is This Answer Correct ? | 0 Yes | 0 No |
Question 77 - The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18, with their respective quantities in N units having the ratio of Na : Nb : Nc = 2 : 3 : 5. (a) Find the numerical average molecular weight of the polymer by using the formula (Ma Na + Mb Nb + Mc Nc) / (Na + Nb + Nc). (b) Find the weighted average molecular weight of the polymer by using the formula (Ma Na Ma + Mb Nb Mb + Mc Nc Mc) / (Ma Na + Mb Nb + Mc Nc). (c) Calculate the polydispersity Q by using the answer in (b) divided by answer in (a). (d) Find the volumetric average molecular weight of the polymer by using the formula (Ma Na Ma Ma + Mb Nb Mb Mb + Mc Nc Mc Mc) / (Ma Na Ma + Mb Nb Mb + Mc Nc Mc). (e) Estimate the polydispersity Q by using the answer in (d) divided by answer in (b).
Are there any alternatives to scraping a shell and tube if a capacity increase will make the pressure drop across the exchanger too large?
What is a good source of information for the design of pressure vessels?
What does the catalystic converter on an automobile do?
what is difference between B.Tech. and B.E. in chemical engineering
What is the maximum recommend pipe velocity for dry and wet gases?
What are the types of clarifier used in water treatement plant?
what is the difference between material balance and mass balance
In which state sulphur exists at 40 degrees temperature and 40 atmospheric pressure in natural gas having sulphur composition 0.1 ppm?
0 Answers Nagarjuna Fertilizers, NFCL,
how to calculate material balnce & energy balnce
7 Answers MahaGenco, Oil India, ONGC,
What particle sizes are electrostatic precipitators used to remove?
What is a good source of equations for calculating discharge flowrates from accidental releases?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
