Is it possible to make 0.75KW motor earthing from MCC panel by using the 1.5 S

Is it possible to make 0.75KW motor earthing from MCC panel by
using the 1.5 SQMM, 4 core cable, means 3 core for 3 Phases &
1 core for Earth terminal?

Question Posted / mahantesh

4 Answers
6928 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Is it possible to make 0.75KW motor earthing from MCC panel by using the 1.5 SQMM, 4 core cable, m..

Answer / najam sultan

For earthing we don't need to use 4 cores, only a single core is enough for earthing.And 1.5sqmm single core cable is enough for earthing of 0.75 kW motor.

Is This Answer Correct ?

4 Yes

3 No

Is it possible to make 0.75KW motor earthing from MCC panel by using the 1.5 SQMM, 4 core cable, m..

Answer / avd

Yes it can be done.Do not worry for fault level because it
will be greaty reduced due to lowersize cable.But make sure
you have installed earth fault protection device to isolate
incase of earth fault.

Is This Answer Correct ?

2 Yes

1 No

Is it possible to make 0.75KW motor earthing from MCC panel by using the 1.5 SQMM, 4 core cable, m..

Answer / mukesh

For motor we need to use 3 cores, only a single core is
enough for earthing.And 1.5sqmm single core cable is enough
for earthing of 0.75 kW motor and double earth is
requirements for whereas 3 phases is used as per rule.

Is This Answer Correct ?

0 Yes

0 No

Is it possible to make 0.75KW motor earthing from MCC panel by using the 1.5 SQMM, 4 core cable, m..

Answer / jyotiranjan sahoo

Yes it can use 1.5 sqmm cable of earthing for that motor but in Indian standard we must be use another body earthing

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

please send me the L&T Emb. sys. placement papers and entire details of pattren

0 Answers HMM, L&T,

IF 8255 CONTROL WORD IS 94H,Tell the chip port work mode ?

0 Answers

A 3PH MOTOR RUNNING IN NORMAL CONDITION AND ITS AMPERE ALSO UNDER ITS FULL LOAD CURRENT,ITS CABLE RATINGS ALSO HIGER THN ITS CAPACITY,BUT ITS CABLE GETTING ABNORMAL HEAT(NOT TOO HOT)WHY ITS GETTING HOT LIK THIS?

5 Answers

what is main advantage if motor connected in star or delta?

3 Answers Essar,

What is the rating of HT SUBSTATION and LT SUBSTATION?

11 Answers NTPC, Sail,

how a circuit breakers work at fault condition .plz give a specified answer.

1 Answers Regen Powertech,

What is magneto on a gas generator. how it functions. its out put is d.c or a.c. how it can be checked for correct functioning

0 Answers

How could a garment factory benefit from renewable energy

0 Answers

CAN ANYBODY EXPLAIN WHAT ACTUALLY MEAN BY THE PHASE DEFFRENCE? R,L,C CIRCUITS?

5 Answers

How frequency meter measuring frequency? What is the principle of frequency meter?

2 Answers

A separately excited dc motor having 2 ohm armature resistsance draws a current of 10A and torque developed is 20 Nm under rated field condtion. the speed of the motor under the rated field condtion , when it is connected to a 100V DC source and delivering 10Nm torque....

2 Answers DRDO,

Need help. 3 phase system. Neutral line arced and melted upon connection of connector with 3 phase power. Why would that happen?

4 Answers

For more Electrical Engineering Interview Questions Click Here