if the length and breath of footing is 1.2m x 1.2 m what will be the length and

Categories >> Engineering >> Civil Engineering
Suggest New Category

if the length and breath of footing is 1.2m x 1.2 m what
will be the length and breath of foundation trench

Question Posted / smita

5 Answers
9783 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

if the length and breath of footing is 1.2m x 1.2 m what will be the length and breath of foundatio..

Answer / jt

1.2+extra width for pcc(.15) =1.35 wide and 1.35 length may
be sufficint for excavation bottom.

Is This Answer Correct ?

11 Yes

3 No

if the length and breath of footing is 1.2m x 1.2 m what will be the length and breath of foundatio..

Answer / neelam saroj

Am not agree with the above posted answer because,
as we all know you can not dig the exact paper size trench
practically on ground,
so, answer could be = length of Footing + extra pcc length
(if not considered then also its Ok)+ extra digging portion
(depends on excavater for its better working)
= 1.2 + 2 X 0.150 + 2 x 0.300
= 2.1m
So Length/Width of trench = 2.1 X 2.1 m

Is This Answer Correct ?

3 Yes

0 No

if the length and breath of footing is 1.2m x 1.2 m what will be the length and breath of foundatio..

Answer / preethi

1.2+.15+.15(extent on both sides)=1.5*1.5 will be the length & breath of foundation trench

Is This Answer Correct ?

2 Yes

0 No

if the length and breath of footing is 1.2m x 1.2 m what will be the length and breath of foundatio..

Answer / senthil

footing base 0.15m&footing tapper 0.3m

Is This Answer Correct ?

2 Yes

2 No

if the length and breath of footing is 1.2m x 1.2 m what will be the length and breath of foundatio..

Answer / protin rabha

Not correct at all. We have to consider extra length and breadth for centering and shuttering also. At least 30 cm both side. So, if footing size is 1.2×1.2m then plus .30m extra both side. Which means size of foundation trench will be 1.5×1.5m. And PCC size can be taken as 150mm extra both sides, which will be 1.35×1.35m PCC size.

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Civil Engineering Interview Questions

Which is the direction of negative angle?

0 Answers

How much steel required in one cubic meter RCC Main girder

1 Answers Isolux Corsan,

Difference between Ghol , Chimney & fly ash bricks b)Floor to floor height is 3m , rise=15cm , tread 20 cm , how to design staircase means steps landing

1 Answers

What is Leastcount of 1. Total station 2. Theodolite 3. Dumpy level 4. Plane Table

3 Answers

If 600mm*200mm*150** size bricks comes 55 piece in one cubic meter then how many 230mm*115mm*75 bricks in one cubic meter

1 Answers Bismi Group,

What is difference between combin footing & rapt footing

0 Answers

If specific gravity of cement is less than 3.15 what is the cause?

0 Answers

How can we cross check the excavation and backfilling quantities.

3 Answers

RR masonry rate analysis

0 Answers

how to compute slab reinforcements on step by step procedures??

1 Answers Juniper Networks,

how to calculate quantity of cement,sand & aggregate for u.c.r / r.r masonry in cm 1:6

0 Answers DBM,

225 mm thick RCC slab, how many ton load slab can carry? for example if 33 ton truck loaded with soil, truck having 6 wheels. slab can take load or not? grade of concrete is M35 and slab design Fe500, slab desing one way slab.

0 Answers

For more Civil Engineering Interview Questions Click Here