why we use tapechanger in primary side of transformer

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / muki7461

5 Answers
8168 Views
Bhel, L&T, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

why we use tapechanger in primary side of transformer ..

Answer / koti

It is not primary, but HV side. For OLTC-above answer of
low current is OK. For Off-Ckt TC; more turns to get more taps, away from core i.e. near to tank which facilitate easy tap connections.

Is This Answer Correct ?

14 Yes

1 No

why we use tapechanger in primary side of transformer ..

Answer / pradyumna171

current of primary side is low i.e smooth control gear is possible in this method of tapping that's why....

Is This Answer Correct ?

14 Yes

6 No

why we use tapechanger in primary side of transformer ..

Answer / raju

Tapings are connected to high voltage winding side, because of low current. If we connect tapings to low voltage side, sparks will produce while tap changing operation due to high current.

Is This Answer Correct ?

9 Yes

1 No

why we use tapechanger in primary side of transformer ..

Answer / renato elamne

_we used a tapchanger in the transformer so that we can select a tapping,same voltages to the primary lines input to the transformer..exam..if 17627 volts primary lines,the tapchanger also point to 17627 taps.

Is This Answer Correct ?

0 Yes

0 No

why we use tapechanger in primary side of transformer ..

Answer / bhabanipattanayak

In a transformer pri. Wdg. Is
always wound over sec. Wdg.
So it is not possible to
connect tap changer in sec.
Side. For this reason we use
tap changer in pri. Side.

Is This Answer Correct ?

3 Yes

4 No

Post New Answer

More Electrical Engineering Interview Questions

If we have 11 kv RYB Phase single core cable near about. Then wht effect and losses

0 Answers Kirloskar,

How many earthings are required for commissioning the Transformer?

14 Answers Dalmia Group, HSL,

in a 740 kw dc seperately excited motor field voltage is constant about 17.4 volts and armature voltage is500 volts dc. how it is possible to have two different voltages from single transformer of output voltage 500 volts? if any difficulty in question contact ajitsingh.kadian@gmail.com

1 Answers

i want to ask that as everybody knows that in star connection on star point is called neutral. my question is that why on that poin called neutral. what is the reason behind it. what is the logic behind it. i heared somewhere that on this point all phases current become zero thats why. if this answer is right then prove why on that point is current become zero. if this answer is not right then tell me the right answer. post ur answer here or on my mail address. m.ikram786@yahoo.com m.ikram555@gmail.com. thanks.

1 Answers

What will be the output voltage of a transformer if it is primarily energized from a square wave voltage source?

0 Answers HPCL,

What is phase cross over frequency?

0 Answers

Which phase is prefered for connecting 1phase vt used for synchronism in an OHL? why?

1 Answers Siemens,

how the testing of protection CT Testing done through Primary injection kit please describe in detail procedure...

0 Answers

-What shall be short circuit current of LV switchgear for a 1000 kva, 11.415kv, 3 phase tranformer with 5% reactance.

0 Answers

why use in & out Diesel line in dg set.

1 Answers NHPC,

explain how to protect high rise building from the risk of lighting.

1 Answers

How do you maintain the batteries for generators, what is the daily maintenance of a generator?

2 Answers Jindal,

For more Electrical Engineering Interview Questions Click Here