I have running 4 generator in paralel.All generators
Voltages is same(470 V),KW also same (100 KW) but only No2
generator Amper is high than another generators.
DG No:1,3,4 470V,100KW, 150 A
DG No:2 470V,100KW,400 A

Answers were Sorted based on User's Feedback



I have running 4 generator in paralel.All generators Voltages is same(470 V),KW also same (100 KW)..

Answer / ruslan

Yes My friend it is possible.All meters are in good
condition.I also surprised.

Is This Answer Correct ?    3 Yes 0 No

I have running 4 generator in paralel.All generators Voltages is same(470 V),KW also same (100 KW)..

Answer / saad

the power formula P=1.732*VICaso according to that if
current will increase active power will also increase so u
check ur meters once again

Is This Answer Correct ?    2 Yes 1 No

I have running 4 generator in paralel.All generators Voltages is same(470 V),KW also same (100 KW)..

Answer / kj

This is caused by kvar. If the excitation is higher (field
voltage) it will take more kvar. This will only be shown by
a current not load. The KW will remain the same.
Reduce the excitation (voltage setting on the AVR) on No 2
generator until it is reading the same current as the other
3 generators.

Is This Answer Correct ?    1 Yes 1 No

I have running 4 generator in paralel.All generators Voltages is same(470 V),KW also same (100 KW)..

Answer / afzaal

what?how could that be possible?with the same power ,the same voltage u get more amps....please check your instruments first..there must be some faulty meters..if not then i am too interested in knowing the answer of it

Is This Answer Correct ?    1 Yes 3 No

Post New Answer

More Electrical Engineering Interview Questions

why did the BDV test in transformer?

2 Answers   Jindal Steel and Power,


How Many safety of Air circuit breaker

2 Answers  


What is means by MacAdam Ellipse?

1 Answers  


Name a govt approved university which have 100% online engineering course.

0 Answers  


Can I use measuring current transformers in protection purposes?

7 Answers  






which type sylbuse involved

1 Answers   BMRCL,


are you hear the meaning of burden , excat meaning of burden in only one word

4 Answers  


If Ac supply is given to the DC motor then what will happen? clear explanation

2 Answers  


why CERAMIC material is used in insulators??

1 Answers  


Why the cost of CT increases with the decreasing of its CT Ratio (Technical Reason)?

2 Answers   Vedanta,


what is the differnce between high impedance relay and low impedance relay

4 Answers   Areva,


WHAT IS PRINCIPLE OF TRANSFORMER

10 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)