Why we use sin wave only in ac not use any other form of wave?

Answers were Sorted based on User's Feedback



Why we use sin wave only in ac not use any other form of wave? ..

Answer / mohammed kamil

We can say that a sinusoidal waveform is rather analog
(continuous) and not discrete (in steps)

Is This Answer Correct ?    3 Yes 1 No

Why we use sin wave only in ac not use any other form of wave? ..

Answer / ashish

SINE WAVE HAS LESS HARMONICS AS COMPARED TO OTHER AC WAVES

Is This Answer Correct ?    2 Yes 0 No

Why we use sin wave only in ac not use any other form of wave? ..

Answer / snigda

It has special properties, one of which is the following. No
other periodic wave will pass through a linear network
containing energy storage elements, (capacitors and inductors)
and leave with the same frequency and shape except for phase
and amplitude changes. All those other waves you mentioned
will not have the same output shape as the input shape. That
is because the derivative and integral of a sinusoidal wave
are the same except for phase differences.

Is This Answer Correct ?    2 Yes 0 No

Post New Answer

More Civil Engineering Interview Questions

what is ph value of water

2 Answers   Adarsh Group,


A doubly reinforced concrete beam is 25 cm wide and 50cm deep to the centre of tension reinforcement. The centre of compression is steel is 5cm from the compression edge. The areas of the compression and the tension steel are 10.16cm2 and 12.56 cm2 if m=18 and the bending moment at the section is 7,000,000 N-cm. Calculate the stress in concrete and steel.

0 Answers  


Tell me about Construction, Contraction and Expansion joints...

2 Answers   Modi Builders, SMCC,


what is Quantity of stone and sand required for one cubic meter of stone work (UCR)

0 Answers  


pointing raju,ayesha says"he is the son of my mother's brother's wife". how is ayesha related to raju?

8 Answers  






How to identify the vitrified tile and ceramic tile by observation only after executing the job.

0 Answers  


Explain what is zoning permit?

0 Answers  


how much aggregate need for 1:4:8 p.c.c in 1sqm area?

5 Answers  


1.Fe500 and Fe550 having more yield strength than Fe415.But why are we prefering Fe415.? 2. d^2/162 formula for knowing the steel wt/m apply all these three? Thanks.

0 Answers  


TELL US ABOUT A TIME WHEN YOU FAILED TO MEET A DEAD LINE. WHAT WERE THE REPERCUSSIONS?

0 Answers  


what is pure bending

1 Answers  


what is the out turn of one masson in plastering, masonary work in 8 hours, with limited healper? what is the out turn of corpender in form work? wood work? in 8 hour with limited healper? what is the out turn of bar bendarin 8 hour with limited healper for slabs, beams, coloumn?

2 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)