Possible cause of IOP alarm in a DP transmitter: a: IOP-minimum b: IOP-Max

Possible cause of IOP alarm in a DP transmitter:

a: IOP-minimum
b: IOP-Maximum

Question Posted / jorriz juico

4 Answers
39678 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Possible cause of IOP alarm in a DP transmitter: a: IOP-minimum b: IOP-Maximum..

if process value is above than instrument range that is IOP
input open and if u remove 24v supply in transmitters it
shows IOP.

Is This Answer Correct ?

37 Yes

2 No

Possible cause of IOP alarm in a DP transmitter: a: IOP-minimum b: IOP-Maximum..

Answer / dass

IOP is an alarm condition where in the input data has become a bad value as a result of disconnection of a detection terminal or process I/O device or the abnormalities of input destination data .

Is This Answer Correct ?

19 Yes

1 No

Possible cause of IOP alarm in a DP transmitter: a: IOP-minimum b: IOP-Maximum..

Answer / nani

if process value in line is very high and loop power 24 v
failed to transmitter

Is This Answer Correct ?

19 Yes

4 No

Possible cause of IOP alarm in a DP transmitter: a: IOP-minimum b: IOP-Maximum..

Answer / ali imran fmb

If the Process value went to over range value due to any reason and frequently triggering alarm on the DCS or SCADA. To avoid this frequent alarm if the DCS or SCADA scanned off or shelving facility is locked, some technicians remove the 24v supply in transmitters then it will trigger alarm input open as well as it will show IOP on the face plate of the this tag number instead of normal. (NR)

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

There is a problem with our HART475 it is not communicating with smart devices error becomes "NO DEVICE FOUND"we have insert 250ohm resistance as per requirement but invain plz tell me the solution?

1 Answers

What is duty of as-built engineer.

2 Answers Sofcon,

How does work A temperature valve or fv control valve in process plz brief me

0 Answers Jindal,

why we use npn sensor in vibration monitoring system

1 Answers

Hi Friends i am going to write BARC written test by this month 20th (20-5-2008). So please if any body knows the details about this or having previous question papers pls mail me to kkumarei@gmail.com. For Suggestions give one message to 9962122264

0 Answers PDIL,

If i want use the 6 kg/cm2 pressure gauge then how to calculate its pressure gauge range?

1 Answers

what is different between 2,3&4 wire rtd and how much maximum distance using plc to field.

0 Answers

What are the key features of a Distributed Control System? describing the various layers (sensor through to business system interfaces) as well as the hardware, software and security aspects of the DCS.

0 Answers

How to calibrate DP transmitter by using HART communicator ?

1 Answers

HOW TO CONVERT 0-60KG/CM2 PRESSURE TRANSMITTER TO A LEVEL TRANSMITTER? CAN WE ABLE TO DO IT? IF YES HOW TO DO IT BY USING HART?

3 Answers

Difference between guide wave radar & non guide wave radar ?

1 Answers UPL,

given a processor batch of 1000 resistors moving on the conveyor belting in a large factory. the resistors is value at 10k ohms each but when the resistors reach the quality control, some of the resistor has been rejected caused by failure in manufacturing.the high quality measurement is used to determine the failure. describe the instrumentation terminology in measurement of a system above with explaining the important in:- -reliability -sensitivity -repeatability -precision -range -resolution -linearity -hysteresis -error -accuracy (answer must related to the scenario above)

0 Answers

For more Instrumentation Interview Questions Click Here