Answer / ch amir islam

We use CASECAD loop to inhance the capability of the
process.normally we use this loop at BFW(boiler feed water)
tanks and at the BMS(burner managment system)to inhance the
burning ratio of fuel that become more relaiable for our
firing.because we are using here two controller(two
setpoints)these both controller makes process much more
flexible and accurate.

Answer / ch amir islam

We use CASECAD loop to inhance the capability of the
process.normally we use this loop at BFW(boiler feed water)
tanks and at the BMS(burner managment system)to inhance the
burning ratio of fuel that become more relaiable for our
firing.because we are using here two controller(two
setpoints)these both controller makes process much more
flexible and accurate.

Answer / www.islamqa.com

Using cascade control enhance loop stability, as the
controller generatea corrective signal in case of any change
in process load - we don't need to wait till we got a
problem in the measured process variable (pressure,
temperature, ..)

Regards,

Ahmed Sabry
Control and Instrumentation Engineer
GPC - General Petroleum Company
CELL.: 00 2 0121367310
ahmedsabry.online@gmail.com

Answer / sreekanth

If a PID Setpoint is derived from another PID then the loop
is called cascade loop.

Answer / vijay patel

cascade loop is used for the control of one perameter buy measure another perameter which is help to enhanse the stability of the loop.

Answer / www.islamqa.com

Using cascade control enhance loop stability, as the
controller generatea corrective signal in case of any change
in process load - we don't need to wait till we got a
problem in the measured process variable (pressure,
temperature, ..)

Regards,

Ahmed Sabry
Control and Instrumentation Engineer
GPC - General Petroleum Company
CELL.: 00 2 0121367310
ahmedsabry.online@gmail.com

ON RADAR INTERFACE LEVEL TRANSMITTER IF DI-ELECRIC IS WRONG WITH CONTINIUS PROCESS THAN HOW CAN INDENTIFY OR HOW CAN I PUT NEW DI-ELECTRIC VALUE?(ROSEMOUNT-TDR-3300-COXIAL PROBE TYPE)

1 Answers   Chevron Phillips,

What is mean by analytical instrumentation?

0 Answers  

Describe the function of Accumulator into the Pump

0 Answers  

what is the principal of flow transmeter,level trans meter,presser transmeter?

11 Answers   Nestle, Reliance,

what do u mean by compensating?in power plant where are compensating done?how level , flow compensated?

1 Answers   TATA,

Hi Friends , i need one urgent help , i am preparing for M.tech entrance examination , i need some obejective questions related to instrumentation field. where can i get those ? can anyone help me pls ?

0 Answers  

what is skin type thermocouple? how it is installed? what is the difference b/w thermocouple & skin type thermocouple? what is gounded & non-grounded thermocoplle? what is the diff b/w these two?

2 Answers   KazStroy Engineering, PSU,

How to calibrate displacer type level transmitter (chemtrol make )for level measurement in hotwell , LP & HP heater ?

0 Answers   Matrix,

what is the difference between single and double compression cable gland

3 Answers   Petrofac,

hi this is noor in my work spot, i arranged THERMOCOUPLE in the place of RTD. (in FEED WATER tank). can i use T/C or not?

10 Answers  

given a processor batch of 1000 resistors moving on the conveyor belting in a large factory. the resistors is value at 10k ohms each but when the resistors reach the quality control, some of the resistor has been rejected caused by failure in manufacturing.the high quality measurement is used to determine the failure. describe the instrumentation terminology in measurement of a system above with explaining the important in:- -reliability -sensitivity -repeatability -precision -range -resolution -linearity -hysteresis -error -accuracy (answer must related to the scenario above)

0 Answers  

what is the full formof HART

7 Answers