ther is any difference if we use 240 V A.C,50 Hz,1 Ph. in place of 230 V A.C,5

ther is any difference if we use 240 V A.C,50 Hz,1 Ph. in
place of 230 V A.C,50 Hz,1 Ph.

Question Posted / guest

4 Answers
6963 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

ther is any difference if we use 240 V A.C,50 Hz,1 Ph. in place of 230 V A.C,50 Hz,1 Ph...

Answer / siva kumar

there is no much difference if we use 240v a.c instead of 230v
a.c

Is This Answer Correct ?

3 Yes

0 No

ther is any difference if we use 240 V A.C,50 Hz,1 Ph. in place of 230 V A.C,50 Hz,1 Ph...

Answer / virendra

Not muuch diffrence

Is This Answer Correct ?

1 Yes

0 No

ther is any difference if we use 240 V A.C,50 Hz,1 Ph. in place of 230 V A.C,50 Hz,1 Ph...

Answer / shakeel

only 10 VA apparent power is lower. no much difference

Is This Answer Correct ?

0 Yes

0 No

ther is any difference if we use 240 V A.C,50 Hz,1 Ph. in place of 230 V A.C,50 Hz,1 Ph...

Answer / arulkumaran

YES, some difference.
example: tube light
if use 240v : * light full brightness
* life time low
if use 230v : * brightness little bit lower than 240v
* life time higher than 240v light.

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

In power point wiring,often,we use less size of earth wire compared to phase & neutral wire and we use big size pin in pug top. how is it justified? can we use small size cable for earthing?

3 Answers HAL,

why does the magnetic balance tests at transformer?

0 Answers

in a refinery one motor is suddenly stoped. what will do how can i findout the problem explain step by step

2 Answers

Up to how much limit of HP of electric motor the Star- Delta Starter can be used ?

1 Answers

Is the inductance parameter of transmission line affected by taking the earth into consideration?is the same true for capacitance? Justify the answer.

1 Answers

what will happen to give a dc supply in transformers?

3 Answers

how to calculate diesel consumption of a D.G.Set?

4 Answers

This is reqd for a 1MW Solar power plant..We have 2DC outputs from the solar panels Connected to 2INVERTOR panels.. Output from invertor is 3ph,280v,500kva,50hz.These are connected to individual ACB.This has to be stepped up to 11KV ,1250KVA SYSTEM.Now can I use (1) one more ACBTO GIVE A COMBINED OUTPUT OF 1000KVA,280V & STEP UP THE OUTPUT BY USING a single two winding 3 ph transformer 11kv/1250kva. or (2)use the two outputs and connect to one three winding transformer of above rating..Pls suggestwith details.

0 Answers

I have a question, I visit 01 site and face a problem, there is 2.5 ton Air Con working, when air con compressor is running at that time rectifier voltages are increasing upto 290-295 v and rectifier is giving main high alarm (rectifier is APC single phase, before starting compressor rectifier voltages was 230v. when air con is going off rectifier voltages are decreasing smoothly at its actual voltages 230v. Load on Genset phases is this: Red-13.5 amp AC (Air Con load), Yellow-1.7 amp AC (BTS lights etc.) and Blew-4 amp AC (telecom system load), Genset phase to phase and neutral to phase voltages are also ok. These are 10 sites having same system and same rectifier APC brand at every site 02 genset are working but the problem is same at all these 10 sites. What will be the reason behind???

1 Answers

If the positive terminal of batteries in 125 v dc system is connected to earth what will happen ?

4 Answers

transformer is working or not with supply of DC?

2 Answers

what is the difference between underreach and overreach.what is the advantage of using overreach instead of underreach.explain

1 Answers

For more Electrical Engineering Interview Questions Click Here