which type of rtd is good for any system,2wire,3wire or 4 wire

Categories >> Engineering >> Instrumentation
Suggest New Category

which type of rtd is good for any system,2wire,3wire or 4
wire

Question Posted / mukesh

9 Answers
15792 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / gobinath

But Generally 3 wire RTD only preparred for Industrial
purpose. Most of the Industires & Design document suggest 3
wire RTD is suitable for any application.

Is This Answer Correct ?

16 Yes

5 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / basit

for long distance and more accuracy we use 3 or 4 wire RTD

Is This Answer Correct ?

5 Yes

0 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / shani_dms

depend on distance if distance too short its should be two
wire
3 and 4 wire used for long distance

Is This Answer Correct ?

9 Yes

5 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / rashidmanzoorkt

If the distance between transmitter and RTD is not long,Any
rtd (2,3 or 4 wire)is suitable.

Is This Answer Correct ?

10 Yes

7 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / bhardwaj**

generally pt100 3-wire rtd is used as third wire
compensates the error and maintains the accuracy of
measurement system

Is This Answer Correct ?

2 Yes

0 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / s vedpathak

3 wire RTD (PT100)is good compare to 4 wire & 2 wire as the
lead wire compensation is achieved in it with less cost.

Is This Answer Correct ?

3 Yes

2 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / ashish namdev, bina refinery [

3 & 4 wire rtd use for temp. compensation from sensor to Tx.
3 wire is good & mostly use.
4 wire is best because in 4 wire, both wire(+ & -) have
compensating cable. then reduce unwanted temp. approximate
negligible. then get correct output.
2 wire have more temp. interference error.

Is This Answer Correct ?

2 Yes

1 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / naseer jarral

3 wire rtd is good bcz thired wire is used to compensate
wire resistence it is a wheet stone bridge

Is This Answer Correct ?

3 Yes

3 No

which type of rtd is good for any system,2wire,3wire or 4 wire..

Answer / m.murali- inst.technologist

Balance two wires are used for compensation, if no. of
compensation cable increases ie compensation resistance become
average.

Is This Answer Correct ?

2 Yes

8 No

Post New Answer

More Instrumentation Interview Questions

what is maximum temprature in instrumentation

1 Answers Sabic,

What is the difference between a double acting and single acting positioner? what type of valves use single acting positioners?

1 Answers AquaTech, NamPower, Samson Resources,

Can i convert 230v ac to 24v dc by using a relay?Instead of Smps is it possible? What is relay logic in plc ?? How it works?

2 Answers Infotech,

What are de-saturators?

0 Answers

Can any body tell me about SAP MAINTINANCE MODULE. WHAT IS its function and application. And study material Source about it. I shall be very thankful.

0 Answers

Dear all... I have 1 0-400 duplex type RTD, I connected the A side to the temperature indicator and B side to the PLC panel, but when I have observed then found that The PLC side temp has the variation. and it was distub to other RTD temp also. so what can I do.pls help me

1 Answers Worley Parsons,

what is plc communication?

2 Answers Siemens,

Can a pneumatic control valve work without positioner?

4 Answers SMC,

cascade controller is feed back or feed forward or both

4 Answers

Q- Why Phase tester is only used for checking AC not DC ?

1 Answers

Why we not use 2-20Ma or 1-20Ma

5 Answers

What is SCADA ? WHAT is it role in DCS ?

3 Answers Honeywell,

For more Instrumentation Interview Questions Click Here