THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / mahesh

12 Answers
30006 Views
APGenco, Lanco, Constant, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / umamahesh

the ratio of V & I is Impedance

Is This Answer Correct ?

42 Yes

7 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / madhusudhana

The ration of V to I in a closed circuit is constant. It is one of the question asked in written exam.

Is This Answer Correct ?

37 Yes

8 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / anita

is always constant..

Is This Answer Correct ?

24 Yes

2 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / raj kumar

impedance

Is This Answer Correct ?

18 Yes

7 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / mahesh somarowthu

Is always Constart

Is This Answer Correct ?

7 Yes

1 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / anusha

the ratio of voltage and current in a closed circuit gives
the equivalent impedance of that circuit and it may vary
depending on the frequency of the supply voltage.

Is This Answer Correct ?

8 Yes

4 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / venugopal reddy bodha

It is always constant................

Is This Answer Correct ?

6 Yes

2 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / sivaroyal

if the supply given to circuit is ac then the ratio is
impedence,
if the supply given to circuit is dc then it is resistence.

Is This Answer Correct ?

4 Yes

2 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / sabeer

The ratio of V and I is Impedance and for closed circuit
impedance is zero

Is This Answer Correct ?

1 Yes

2 No

THE ROTIO OF VOLTAGE AND CURRENT IN A CLOSED CIRCUIT..

Answer / chanti

zero

Is This Answer Correct ?

3 Yes

5 No

Post New Answer

More Electrical Engineering Interview Questions

why we are using in reverse power relay in generator singranizing

1 Answers Dalkia,

Alternator couple to diesel engine why, Alternator couple to ac service motor with gear drive for 1500 rpm possible (yes or no) aim to low input power supply give to motor then high output power taken for alternator Please answer this question

1 Answers Turbo,

Power Factor Correction Panel (Manual & Automatic)

1 Answers

as ac supply is given 2 the transformer why it doesnot depends upon powerfactor????

2 Answers

What is basic difference between Soft Starters And VFD drives?

19 Answers IBM,

what is charger supervision and control supervision?

1 Answers

How much area is covered by a single lightning arrestor to protect object from lightning strokes ?

1 Answers

In stepdown transformer 11/415 volt two nos.(R & Y)HT side fuse is blown ,what will be voltage of ry,rb,yb in secondary side

5 Answers NTPC,

if single phase is 230 v three phase is 440 v then what about two phase?and why is it so?

2 Answers Eicher,

what is the function AND aplication of CBCT?

2 Answers

what is the difference between KW and KWh?

9 Answers

Application Comparison between 22KV (UE)and 33KV (E) system. Are we allowed to use 33KV (E) cable in lieu of 22KV (UE) cable. What are the technical disadvantages.

1 Answers

For more Electrical Engineering Interview Questions Click Here